Ingresso Binario KNX DATEC 1630.03160/62100 – 8 Canali da Incasso con 8 LED di Stato.

English description pending.

• Eight completely programmable independent touch areas. 
• Includes a discretized PI regulator to achieve greater comfort and energy savings. 
• Built-in humidity sensor. 
• Dew point measurement according to relative humidity and temperature. 
• Arithmetic Logic Unit 
• Timers/counters.
• Also available in the White version

The Sensor On-Off Dim Up-Down KNX MicroWave is a dual technology infrared and microwave sensor. The sensor is used to detect the presence of moving people. It is possible to set the operation of the Sensor On-Off Dim Up-Down KNX or infrared only, microwave or both. It is also equipped with a brightness sensor with the possibility of setting the light source: internal, external. In the Sensor On-Off Dim Up-Down KNX the brightness function can be used alone or in combination with the detection function.When the brightness sensor is combined with detection it will be necessary that the requirements of both settings are met. The use of the sensor is suitable for residential, commercial and tertiary environments.

Attuatore KNX Motor Control DATEC 1630.03141/65100 – Comando Ventilatore a Soffitto da Incasso 230VAC 100W.

English description pending.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless wall-mounted Infrared PIR motion detector for lighting control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• As soon as it detects movement, the sensor sends the ON signal to the linked receiver and its
  contact keeps closed. The ON time must be set on the receiver.
• Wall or ceiling mounting installation.
• Coverage: 180º and Ø10m at 2m high.
• Power Supply: 2 x 3V AA Lithium batteries L91. Working life over 15 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: IT KNX 001, MI KNX 001 & CO KNX 002.

• Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• It has 2 operation modes:
  · Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 & CO KNX 002.
  · Presence detector: useful for heating and air conditioning control.
• Compatible with the actuators: TM KNX 001 & CO KNX 002.
• Incorporates Temperature sensor
• Coverage: 360º and Ø7m at 2,5m high.
• Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
• Radio-frequency: 868,4MHz.

• Wireless Luminosity sensor transmitter for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brigthness value to the lighting actuator for constant light control operation.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

High-frequency motion detector HF 3360, ideal for basement corridors, stairwells, multi-storey car parks, installation height 2.8 m, 360° angle of coverage, reach 1 – 8 m (radial), detection regardless of temperature, HF-sensor technology also detects movement through glass, wood and stud walls. 

Infrared presence detector Presence Control PRO IR Quattro HD KNX for indoors, ideal for medium to large-size offices, conference and meeting rooms, classrooms and lecture theatres, sports halls and warehouses,installation height up to 10 m,controll 4 lighting channels and HVAC,4800 switching zones for the ultimate in detection quality, presence detection over a true 64 m2, square detection zone. 

IS 3360 MX Highbay motion detector – ideal for high ceilings in industrial buildings or commercial properties. For mounting heights of up to 14 m. High-precision 360° infrared sensor. Maximum reach: 18 m. For watching over up to 1000 sq.m  

IS 3360 MX Highbay motion detector – ideal for high ceilings in industrial buildings or commercial properties. For mounting heights of up to 14 m. High-precision 360° infrared sensor. Maximum reach: 18 m. For watching over up to 1000 sq.m 

It is possible to adjust the presence sensor sensitivity in an easy way,selecting between 3 different levels or personalizing by yourself.It includes parameters to define regulation steps,to establish deviations, or to calibrate it.It is also possible to change between auto and manual mode, defining the behavior when it changes between those two options.It also includes an additional thermostat 

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

EAE Attuatore Fan Coil FCA100 KNX – Controllo Ventilconvettori 2/4 Tubi, Valvola Triac/0-10V.

English description pending.

EAE Multi Input/Output MIO1616 – 16 Ingressi e 16 Uscite KNX per Pulsanti e Spie.

English description pending.

MD100 KNX movement detector is used in indoor spaces with integrated light sensor to achieve presence detection and constant light functions in a single device.

• Flush or surface mount options
• 9m in diameter movement detection at 2.5 m assembly height
• Integrated light level sensor and movement sensor to achieve constant light function
• Possibility to control air conditioning and ventilation through HVAC
• Adjustable brightness level and duration for “Movement”, “After Movement”, and “No Movement” functions
• Two constant light level adjustments for two states: Vacant & Occupied
• Ability to send movement status periodically with a separate communication object
• Feature to operate as a single sensor when connected with other KNX presence sensors
• Test and calibration modes for convenience during installation
• Does not require an external power supply

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

EAE Interfaccia Universale KNX UI108 – 8 Canali, 6 Modalità Operative.

English description pending.

Colored connection cables

Flush mounted into switch boxes

Does not require an external power supply

8 input channels with each featuring following functions:

• Switching
• Dimming
• Curtain control
• Value and priority
• Scene control
• Pulse counter

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

EAE Attuatore KNX SA108 – 8 Canali 16A, Corrente di Spunto 500A.

English description pending.

In addition to switching resistive loads, SA108 is designed to be used with capacitive and inductive loads, enabling a convenient control of fluorescent ballasts and led drivers.

8 independently configurable channels

Manual control for each relay on the device using slide switches

Does not require an external power supply

Electric current control can be configured

Following functions can be defined separately for each channel:

• Stair function
• External logic
• Internal logic
• Priority function
• Threshold function
• Transaction time
• Sweep function

Download   DATASHEET

Download   MANUALE 

Download   DATABASE ETS

EAE Attuatore KNX SA104 – 4 Canali 16A, Corrente di Spunto 500A.

English description pending.

In addition to switching resistive loads, SA104 is designed to be used with capacitive and inductive loads, enabling a convenient control of fluorescent ballasts and led drivers.

4 independently configurable channels

Manual control for each relay on the device using slide switches

Does not require an external power supply

Electric current control can be configured

Following functions can be defined separately for each channel:

• Stair function
• External logic
• Internal logic
• Priority function
• Threshold function
• Transaction time
• Sweep function

Download   DATASHEET

Download   MANUALE 

Download   DATABASE ETS

iSwitch is a wall-mounting room controller device for on/off switching of loads, dimming of lighting devices, control of motor drives or other programmable switching and control functions. The product is equipped with integrated temperature sensor, humidity sensor and ambient sensor. iSwitch can act as a room probe or thermostat, both in heating and cooling mode.Body gateway included

Infrared motion detector IS 345 MX Highbay for indoors, ideal for large heights in depots, high-bay warehouses, machine shops, check-in areas and departure lounges, installation height 14 m, detection zone 30 x 4 m (radial), large terminal compartment for easy installation. Available as square surface-mounted and concealed version.  

• Detection of air quality
  (CO2-concentration, rel. humidity, temperature)
• CO2-sensor (Measuring range 390–10.000 ppm)
• CO2-value is atmospheric pressure compensated
• Sensors for CO2-, temperature, humidity and atmospheric pressure measurement
• Humidity sensor (Measuring range 0...100% rel. humidity)
• Temperature sensor (Measuring range 0°/50°C)
• 5 binary and analogue inputs

• Capacitive touch sensor for up to 25mm material size
• Three sensor panels enable button, double-click and wiping-gesture (acustic feedback customizable)
• Sensor panels can be used as one big panel
• Up to six switching options (acustic feedback customizable)
• Plastic housing (210x140x11 mm) robust against splash water
• Reset time programmable by switching timer
• KNX-Bus power required only

It is able to drive a 5 A per channel, 12-24 VDC LED strip – that is a sum of 480 Watt dimming power or 120 Watt for each channel for 24 V LEDs.In device additionally a 16 A switching actuator with two timers is integrated. Thus, the LED power supply is powered on by the actuator if needed or turned off to minimize standby losses of the LED power supply. 

It is able to drive a 5 A per channel, 12-24 VDC LED strip – that is a sum of 480 Watt dimming power or 120 Watt for each channel for 24 V LEDs.In device additionally a 16 A switching actuator with two timers is integrated. Thus, the LED power supply is powered on by the actuator if needed or turned off to minimize standby losses of the LED power supply. 

• Voltage: 24 V DC via KNX BUS
• typ. power input: 7 mA
• Detection area: vertical 360°
• Range:
  max. Ø 24 m across
  max. Ø 8 m towards
  max. Ø 6,4 m smaller movements
• Recommended mounting height: 2.5 m
• Degree / class of protection: IP20 / Class II
• Ambient temperature: -25 °C to +55 °C
• Housing: Polycarbonate, UV-resistant
• Brightness set value: 5 - 1200 Lux 

Uscita Analogica KNX DATEC 1630.02131/57100 – 4 Canali 0-10V DIN per Valvole, Ventilazione e Motori.

English description pending.

Attuatore Dimmer KNX Weinzierl IO 530 (1D2I) – 1 Canale Dimmer 230V + 2 Ingressi Binari, 1TE.

English description pending.

The Universal dimming actuator KNXIO 530 (1D2I) is a compact mains dimmer for 230 V ~ with one output and two binary inputs. The dimming actuator supports phase control or phase section and is thus suitable for all dimmable 230 V lamps (eg incandescent lamps, dimmable LED lamps, halogen lamps). The dimming channel offers various comfort functions, including scenes, automatic, snooze function, staircase lighting and sequencer.The inputs of Universal dimming actuator KNXIO 530 (1D2I) can be controlled via conventional switches with an external voltage of 230 V. In addition to the output and input channels, the Universal dimming actuator KNXIO 530 (1D2I) contains 16 independent logic or timer functions. Two buttons and three LEDs on the front of the device allow local operation and visualization of the device status.

The Blind Actuator KNX IO 520 (1J2I) is a compact blind actuator with two additional binary inputs. The actuator is used to control a blind, a shutter or a window drive. The relay contacts are electrically interlocked. The inputs Blind Actuator KNX IO 520 (1J2I) can be connected to conventional switches with an external voltage of 12 to 230 V. In the not configured state the binary inputs control the actuator channel. Via commissioning the device using ETS® software the binary inputs can be used independently. Two push buttons and three LEDs allow a local operation and a visualization of the device state. In addition to the output and input channels the Blind Actuator KNX IO 520 (1J2I) includes 16 independent functions for logic or timer control.

• ▪ 1 shutter output, 230 V∿, 8 A
• ▪ Drive directions electro-mechanically locked against each other
• ▪ For blinds, shutters or window drives
• ▪ Approach position via time calculation
• ▪ 2 inputs 12..230 V⎓∿, galvanically isolated
• ▪ Switching, dimming, shutters, scenes, pulse counter
• ▪ Integrated logic and timer functions
• ▪ Connections: KNX, plugable screw terminals for IO
• ▪ For DIN rail, width 1 unit (18 mm)

Attuatore di Commutazione KNX Weinzierl IO 511.1 secure (1O2I) – 1 Uscita Relè 230V/16A + 2 Ingressi, Sostituto Relè a Impulsi.

English description pending.

Compact KNX actuator: 1 relay output 230V~/16A + 2 binary inputs galvanically isolated. KNX replacement for impulse switches. KNX Security. 1 DIN module. Art. 5327.

Attuatore di Commutazione KNX Weinzierl IO 510.1 secure (2O) – 2 Uscite Relè 230V/10A, KNX Data Security.

English description pending.

Compact KNX switching actuator with 2 bistable relay outputs 250V~/10A. Staircase function, heating actuator, integrated logic, KNX Security. 1 DIN module (18 mm). Art. 5444.

Pulsante Wireless KNX Weinzierl RF/ENO Push Button 440 secure – Ibrido KNX RF + EnOcean, Serie MATCH 55.

English description pending.

The KNX RF / ENO Push Button 440 secure unites two wireless protocols in one device: EnOcean and KNX RF. Out of the box the push button operates in EnOcean mode. EnOcean Secure can be enabled via pressing a key combination. By configuration with the ETS® the push button switches to KNX RF mode with optional support of KNX Data Security. Via a factory reset the device can be switched back to EnOcean protocol.

Alimentatore KNX Weinzierl PowerSupply USB 367 – 640mA con Display OLED, Interfaccia USB e Funzioni Logiche.

English description pending.

USB POWER SUPPLY 367 KNX Secure is a 640 mA bus power supply with high efficiency and a small footprint of only 4 units (72 mm). The USB POWER SUPPLY 367 KNX Secure device has a bus choke, an integrated USB interface (Micro USB connector) and additionally provides an output for auxiliary power supply. Via the integrated KNX node USB POWER SUPPLY 367 KNX monitors the output current, the bus voltage and the temperature in the switchgear. The 367 KNX Secure device has various logic functions for application purposes. The configuration of the 367 KNX Secure is done with the ETS (version 4.2 or later). An easy to read OLED display on the front panel allows the user to view the operating parameters locally on the USB POWER SUPPLY 367 KNX Secure. This USB interface can be used to program KNX Secure devices with the ETS.

PD100 KNX presence detector is used in indoor spaces with integrated light sensor to achieve presence detection and constant light functions in a single device.

• Flush or surface mount options
• 6m in diameter movement detection at 2.5 m assembly height
• Integrated light level sensor and movement sensor to achieve constant light function
• Possibility to control air conditioning and ventilation through HVAC
• Adjustable brightness level and duration for “Movement”, “After Movement”, and “No Movement” functions
• Two constant light level adjustments for two states: Vacant & Occupied
• Ability to send movement status periodically with a separate communication object
• Feature to operate as a single sensor when connected with other KNX presence sensors
• Test and calibration modes for convenience during installation
• Does not require an external power supply

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

Presence detector with radio- frequency technology for hidden installation. 360º detection through non-metallic surfaces for installation in technical and false ceilings.Safe against sabotage and non- desired manipulation due to its hidden installation. Suitable for lighting, motion detection, intrusion control, etc.

Kristall offers all the safety and durability advantages of a capacitive keyboard, since there is no mechanical wear of any kind, and ease of use is improved with the introduction of luminous and acoustic feedback.Kristall offers the complete KNX command set needed to control any type of device: On/Off commands, light dimming, window actions and transmission of scenarios.