New products
New products
Radio Frequency Devices (RF)
In places where wiring is not possible, KNX-RF devices allow to control lighting, shutters or heating and cooling by transmitting wireless data inside a building.
Subcategories
-
![DINUY RF KNX DOOR/ WINDOW SENSOR]()
- -10%
-
![DINUY RF KNX UNIVERSAL DIMMER & LED LAMPS]()
- -10%
DINUY KNX RF/TP Coupler
€355.00 -10% €319.50- The KNX RF / TP coupler is a compact KNX Radio coupler. Connect the KNX RF devices of a radio line with the KNX Twisted Pair Bus.
- You have a filter table (8k bytes).
- Supports long frames compatible with ETS® ETS5 or higher software.
- The keys on the front allow you to disable the telegram filter for testing purposes.
- The LEDs indicate the operating conditions and communication errors on the KNX bus.
- The power supply is supplied via the KNX bus (main line).
- Programming and commissioning using ETS5 or later.
-
![DINUY One Channel interface 2-Fold Pushbutton]()
![]()
- -10%
DINUY RF One Channel...
€86.55 -10% €77.90- One channel interface for 2-fold pushbutton.
- Switch ON/OFF: Connects or disconnects the linked actuator. ON or OFF is sent depending on which of the two buttons is pressed.
- Dimmer: Connects, disconnects or dims the linked actuator. It sends ON/OFF or Dimming_Up/Dimming_Down depending on which of the two buttons is pressed the duration of the action.
- Blinds/Shutters: Controls a linked blind actuator. It sends Step_Up/Step_DOwn or Move_Up/Move_Down depending on which of the two buttons is pressed and the duration of the action.
- Scenes: Saves and recovers two different scenes (one scene in each button). It sends Scene_Save or Scene_Load depending on the duration of the action.
- Installaton in standard mechanism box, behind pushbutton.
- Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX DMS, RE KNX LE1 & RE KNX LE2.
-
![DINUY RF KNX 1-channel Switch actuator General Purpose]()
- -10%
DINUY RF KNX 1-channel...
€162.12 -10% €145.91- Wireless 1-channel Switch actuator for general purpose.
- Up to 16A switching capacity with non-free voltage output.
Two different operation modes:
· Switch ON/OFF.
· Timer: 3sec ~ 5min. - Incorporates RF signal repeater function, which can be enabled or disabled as needed.
- A conventional pushbutton can be wired for local control.
- DIN-rail mounting. Dimensions: 1 module wide.
- 230V-operated.
- Radio-frequency: 868,4MHz.
- Range: up to 100m (in the free field).
- Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.
-
![DINUY RF KNX 1 CHANNEL PORTABLE PUSHBUTTON]()
- -10%
DINUY RF KNX 1 CHANNEL...
€124.00 -10% €111.60- The 1-channel Pushbutton sends KNX telegrams when the button is pressed depending on its parameterisation through its switches.
- The device provides functions like switching or dimming of lighting, moving of blinds and shutters,managing scenes,…
- Dimensións: 78 x 28 x 23mm.
- Portable or wall fix mounted.
- Switch ON / OFF & Toggle: connects, disconnects or switches the linked actuator. It sends On / OFF / Toggle depending on the configuration.
- Dimmer: connects, disconnects or dims the linked actuator. It sends On / Off / Toggle or Dimming_Up / Dimming_ Down depending on the configuration.
- Blinds / Shutters: controls a linked blind actuator. It sends Step_Up / Step¨_Down or Move_Up / Move_ Down depending on the configuration.
- Scenes: saves and recovers one scene (0…4) depending on the configuration.
- Battery-operated: 2 x 3V Lithium batteries CR2025. Useful life higher than 8 years.
Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.
-
![DINUY RF KNX 2-CHANNEL ON/OFF / 1-CHANNEL BLIND/SHUTTER ACTUATOR]()
- -10%
DINUY RF KNX 2-CHANNEL...
€188.20 -10% €169.38- Wireless 1-channel blind/shutter actuator or 2-channel switching actuator.
- Up to 16A switching capacity per channel with 2 free-voltage outputs.
- Incorporates RF signal repeater function, which can be enabled or disabled as needed.
- Includes 2 auxiliary inputs which allow the local control.
- Dimensions: 107 x 53 x 34mm.
- 230V-operated.
- Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 002 & CO KNX 002.
-
![DINUY RF KNX Radio Remote Control 5 Channels 5 Scene]()
- -10%
DINUY RF KNX Radio Remote...
€190.00 -10% €171.00- The Radio Remote Control sends KNX telegrams when one of the keys is presse depending on its parameterisation.
- The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
- Incorporates 5 independent channels, 1 main channel and 5 scene channels.
- Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
- Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
- Radio-frequency: 868,4MHz.
- Range: up to 100m (in the free field).
- Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.
-
![DINUY RF KNX THERMOSTAT]()
- -10%
DINUY RF KNX THERMOSTAT
€195.71 -10% €176.14- Wireless 1-channel Thermostat actuator for HVAC control.
- It incorporates a potentiometer which allows setting the desired temperature avoiding any undesired manipulation.
- Every time it receives a signal of temperature from the sensor it will be compared with the already set in the thermostat and will act accordingly on its relay.
- It also can receive telegrams from door/window contacts or presence detectors.
- Up to 16A switching capacity with free-voltage relay.
- Incorporates RF signal repeater function, which can be enabled or disabled as needed.
- Modular installation device. DIN-rail mounting. 1-module wide.
- 230V-operated.
- Radio-frequency: 868,4MHz.
- Range: up to 100m (in the free field).
- Compatible with: SE KNX 001, SE KNX 003, SE KNX 004, DP KNX 001 & CO KNX 002.
-
![DINUY RF KNX WIRELESS BRIGHTNESS SENSOR FOR SOLAR PROTECTION]()
- -10%
DINUY RF KNX WIRELESS...
€147.09 -10% €132.38- Wireless Luminosity value transmitter for Sun protection function.
- It is designed for the automatic control of shutters or blinds.
- According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
- Luminosity is measured by the sensor attached to the window with a sticker.
- Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
- Dimensions: 78 x 28 x 23mm.
- Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
- Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
- Radio-frequency: 868,4MHz.
- Range: up to 100m (in the free field).
- Compatible with: PE KNX 001 & CO KNX 002.
-
![DINUY RF KNX TEMPERATURE SENSOR]()
- -10%
DINUY RF KNX TEMPERATURE...
€144.79 -10% €130.31- Wireless Temperature value transmitter.
- Sends the temperature value measured in the place when:
· The temperature value changes more than ±0,5ºC.
· 60 minutes after the last transmission.
· Pressing the inside link key. - Dimensions: 78 x 28 x 23mm.
- Portable or wall fix mounted.
- Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
- Radio-frequency: 868,4MHz.
- Range: up to 100m (in the free field).
- Compatible with: TM KNX 001 & CO KNX 002.
-
![DINUY RF KNX TEMPERATURE SENSOR SETTING KNOB]()
- -10%
DINUY RF KNX TEMPERATURE...
€147.92 -10% €133.13- Wireless Temperature sensor with desired temperature value control knob.
- This sensor sends the following variables:
· Measured temperature value.
· Temperature setpoint value.
· State (Standby or Auto). - Incorporates a wheel to set the desired temperature in the room.
- Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
- Dimensions: 80 x 30 x 26mm.
- Radio-frequency: 868,4MHz.
- Range: up to 100m (in the free field).
- Compatible with: TM KNX 001 & CO KNX 002.
-
![DINUY RF KNX TEMPERATURE SENSOR]()
- -10%
DINUY RF KNX TEMPERATURE...
€204.87 -10% €184.38- Wireless Temperature value transmitter.
- Sends the temperature value measured in the place when:
· The temperature value changes more than ±0,5ºC.
· 60 minutes after the last transmission.
· Pressing the inside link key. - Dimensions: 78 x 28 x 23mm.
- Portable or wall fix mounted.
- Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
- Radio-frequency: 868,4MHz.
- Range: up to 100m (in the free field).
- Compatible with: TM KNX 001 & CO KNX 002.
