Ingresso Binario KNX DATEC 1630.03160/62100 – 8 Canali da Incasso con 8 LED di Stato.

English description pending.

• Eight completely programmable independent touch areas. 
• Includes a discretized PI regulator to achieve greater comfort and energy savings. 
• Built-in humidity sensor. 
• Dew point measurement according to relative humidity and temperature. 
• Arithmetic Logic Unit 
• Timers/counters.
• Also available in the White version

The Sensor On-Off Dim Up-Down KNX MicroWave is a dual technology infrared and microwave sensor. The sensor is used to detect the presence of moving people. It is possible to set the operation of the Sensor On-Off Dim Up-Down KNX or infrared only, microwave or both. It is also equipped with a brightness sensor with the possibility of setting the light source: internal, external. In the Sensor On-Off Dim Up-Down KNX the brightness function can be used alone or in combination with the detection function.When the brightness sensor is combined with detection it will be necessary that the requirements of both settings are met. The use of the sensor is suitable for residential, commercial and tertiary environments.

Basic functionality of the TP line coupler ITR901-002 is coupling two KNX TP lines (main line and subline) providing galvanic isolation in between. Due to its flexibility ITR901-002 coupler unit can be used as KNX line coupler or KNX area coupler (to connect a TP line to a TP area or backbone) or KNX repeater (without filtering). Operational and filtering states, malfunction and faulty communication are indicated by LEDs. 

Download  DATASHEET

Download DATABASE ETS

• Wireless wall-mounted Infrared PIR motion detector for lighting control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• As soon as it detects movement, the sensor sends the ON signal to the linked receiver and its
  contact keeps closed. The ON time must be set on the receiver.
• Wall or ceiling mounting installation.
• Coverage: 180º and Ø10m at 2m high.
• Power Supply: 2 x 3V AA Lithium batteries L91. Working life over 15 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: IT KNX 001, MI KNX 001 & CO KNX 002.

• Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• It has 2 operation modes:
  · Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 & CO KNX 002.
  · Presence detector: useful for heating and air conditioning control.
• Compatible with the actuators: TM KNX 001 & CO KNX 002.
• Incorporates Temperature sensor
• Coverage: 360º and Ø7m at 2,5m high.
• Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
• Radio-frequency: 868,4MHz.

• Wireless Luminosity sensor transmitter for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brigthness value to the lighting actuator for constant light control operation.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

High-frequency motion detector HF 3360, ideal for basement corridors, stairwells, multi-storey car parks, installation height 2.8 m, 360° angle of coverage, reach 1 – 8 m (radial), detection regardless of temperature, HF-sensor technology also detects movement through glass, wood and stud walls. 

Infrared presence detector Presence Control PRO IR Quattro HD KNX for indoors, ideal for medium to large-size offices, conference and meeting rooms, classrooms and lecture theatres, sports halls and warehouses,installation height up to 10 m,controll 4 lighting channels and HVAC,4800 switching zones for the ultimate in detection quality, presence detection over a true 64 m2, square detection zone. 

IS 3360 MX Highbay motion detector – ideal for high ceilings in industrial buildings or commercial properties. For mounting heights of up to 14 m. High-precision 360° infrared sensor. Maximum reach: 18 m. For watching over up to 1000 sq.m  

IS 3360 MX Highbay motion detector – ideal for high ceilings in industrial buildings or commercial properties. For mounting heights of up to 14 m. High-precision 360° infrared sensor. Maximum reach: 18 m. For watching over up to 1000 sq.m 

It is possible to adjust the presence sensor sensitivity in an easy way,selecting between 3 different levels or personalizing by yourself.It includes parameters to define regulation steps,to establish deviations, or to calibrate it.It is also possible to change between auto and manual mode, defining the behavior when it changes between those two options.It also includes an additional thermostat 

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

KNX EnOcean 636 Secure Gateway is a bidirectional gateway between EnOcean wireless devices and the KNX bus. With the KNX EnOcean 636, commands and measured values from wireless EnOcean sensors can be transmitted to the KNX bus. It allows both KNX actuators and EnOcean actuators to be controlled via the KNX bus. The KNX EnOcean 636 Secure Gateway supports encrypted radio communication with security-enabled EnOcean devices. In addition, the Secure Gateway provides control and logic functions and includes a wireless repeater. The KNX EnOcean 636 supports more than 100 profiles with its 32 radio channels. Enables easy and secure connection of various KNX devices and EnOcean sensors and actuators. Commissioning is as simple as usual: With all 32 channels, encryption can be activated individually. Subsequently EnOcean sensors and actuators, which support safety, can be taught in. The user gets more safety without loss of comfort.

EAE Attuatore Fan Coil FCA100 KNX – Controllo Ventilconvettori 2/4 Tubi, Valvola Triac/0-10V.

English description pending.

EAE Multi Input/Output MIO1616 – 16 Ingressi e 16 Uscite KNX per Pulsanti e Spie.

English description pending.

EAE Accoppiatore di Linea KNX LC200 – Filtro Traffico, Ripetitore, ETS4.2.

English description pending.

EAE Interfaccia IP KNX IPI200 – Tunneling KNXnet/IP, 5 Connessioni Simultanee.

English description pending.

EAE Gateway KNX/Modbus KMG103 640mA – Alimentatore KNX Integrato per Hotel.

English description pending.

EAE Gateway KNX/Modbus KMG103 320mA – Alimentatore KNX Integrato per Hotel.

English description pending.

EAE Alimentatore KNX PS320 – 320mA con Uscita Ausiliaria 30V DC.

English description pending.

EAE KNX Power Supply - 320 mA version. Features an additional 30V DC output, NOT to power an additional KNX bus.

EAE Alimentatore KNX PS640 – 640mA con Uscita Ausiliaria 30V DC.

English description pending.

EAE KNX Power Supply - 640 mA version. Features an additional 30V DC output, NOT to power an additional KNX bus.

MD100 KNX movement detector is used in indoor spaces with integrated light sensor to achieve presence detection and constant light functions in a single device.

• Flush or surface mount options
• 9m in diameter movement detection at 2.5 m assembly height
• Integrated light level sensor and movement sensor to achieve constant light function
• Possibility to control air conditioning and ventilation through HVAC
• Adjustable brightness level and duration for “Movement”, “After Movement”, and “No Movement” functions
• Two constant light level adjustments for two states: Vacant & Occupied
• Ability to send movement status periodically with a separate communication object
• Feature to operate as a single sensor when connected with other KNX presence sensors
• Test and calibration modes for convenience during installation
• Does not require an external power supply

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

EAE IP Router KNX IPR100 – Connessioni KNXnet/IP.

English description pending.

EAE KNX IP router is used as a line or backbone coupler to ensure communication between KNXnet/IP and TP KNX bus line. Electrical insulation is also achieved between the linked lines.

• EAE KNX IP router is a tunneling and routing device. IPR100 is used as a gateway between IP and KNX bus line for commissioning and monitoring purposes. (It is also possible to simultaneously create 4 KNXnet/IP connections).
• Simultaneous connection to two different KNX systems and transmission of telegrams between the local network and different buses
• IP address assignment manually or by DHCP server
• Option to block or allow telegrams between KNX and IP regarding configured filter table
• Deactivation of filter table using on-device buttons for quick diagnosis
• Functional status information with 6 LEDs on device

Download DATASHEET

Download MANUALE PRODOTTO

Download DATABAESE ETS

EAE Interfaccia Universale KNX UI108 – 8 Canali, 6 Modalità Operative.

English description pending.

Colored connection cables

Flush mounted into switch boxes

Does not require an external power supply

8 input channels with each featuring following functions:

• Switching
• Dimming
• Curtain control
• Value and priority
• Scene control
• Pulse counter

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

iSwitch is a wall-mounting room controller device for on/off switching of loads, dimming of lighting devices, control of motor drives or other programmable switching and control functions. The product is equipped with integrated temperature sensor, humidity sensor and ambient sensor. iSwitch can act as a room probe or thermostat, both in heating and cooling mode.Body gateway included

Infrared motion detector IS 345 MX Highbay for indoors, ideal for large heights in depots, high-bay warehouses, machine shops, check-in areas and departure lounges, installation height 14 m, detection zone 30 x 4 m (radial), large terminal compartment for easy installation. Available as square surface-mounted and concealed version.  

• Detection of air quality
  (CO2-concentration, rel. humidity, temperature)
• CO2-sensor (Measuring range 390–10.000 ppm)
• CO2-value is atmospheric pressure compensated
• Sensors for CO2-, temperature, humidity and atmospheric pressure measurement
• Humidity sensor (Measuring range 0...100% rel. humidity)
• Temperature sensor (Measuring range 0°/50°C)
• 5 binary and analogue inputs

• Communication with 8 IP cameras with 8 input and 8 output objects each
• Transfer of the camera events to the KNX bus
• Controlling the camera via the KNX bus
• KNX Bus Terminal and Ethernet / IP Connection (POE)
• Suitable for IP cameras that meet the communication requirements as described in the camera settings in the manual
• Configuration via ETS 5

• Capacitive touch sensor for up to 25mm material size
• Three sensor panels enable button, double-click and wiping-gesture (acustic feedback customizable)
• Sensor panels can be used as one big panel
• Up to six switching options (acustic feedback customizable)
• Plastic housing (210x140x11 mm) robust against splash water
• Reset time programmable by switching timer
• KNX-Bus power required only

• Up to 48 telegrams/second routing performance
• Up to 35 telegrams/second tunnelling performance
• Up to five KNXnet/IP tunnel connections
• Integrated display
• 10/100 MBit Ethernet interface
• Power over Ethernet or ext. 16-24 AC or 20-30V DC
• Battery buffered RTC
• SNTP server
• Telnet server

• • Up to 48 telegrams/second routing performance
  • Up to 35 telegrams/second tunnelling performance
  • Up to five KNXnet/IP tunnel connections
  • Integrated display
  • 10/100 MBit Ethernet interface
  • Power over Ethernet or ext. 16-24 AC or 20-30V DC
  • Battery buffered RTC
  • SNTP server
  • Telnet server

IT is a bidirectional meter for measurement of active and reactive energy or power, respectively. Further it features an analysis of power supply quality.Measurements can be performed in a 3-phase system or in three independent 1-phase system.(current, voltage, active power, reactive power, active energy, reactive energy, power factor, THD-U, THD-I harmonics, unbalanced load, zero system current) 

• Voltage: 24 V DC via KNX BUS
• typ. power input: 7 mA
• Detection area: vertical 360°
• Range:
  max. Ø 24 m across
  max. Ø 8 m towards
  max. Ø 6,4 m smaller movements
• Recommended mounting height: 2.5 m
• Degree / class of protection: IP20 / Class II
• Ambient temperature: -25 °C to +55 °C
• Housing: Polycarbonate, UV-resistant
• Brightness set value: 5 - 1200 Lux 

voltage input: 230 V AC (50Hz)

output current: 960 mA

Integrated choke

LEDs for operation, bus reset and programming mode

Integrated bus-connection with voltage and current measurement

Data output on KNX bus via group object and visible on display

KNX objects for voltage, current and power measurements

KNX alarm functions

Housing temperature measurement

AUX with 600mA additional output

Alimentatore KNX 640mA DATEC 1630.02150/90100 DIN con Uscita Ausiliaria 30V.

English description pending.

KNX IP LineMaster 762.1 secure - Alimentatore Bus con Router IP e Interfaccia Secure.

English description pending.

The KNX IP LineMaster 762.1 secure combines the essential functions of a KNX bus line: KNX power supply with choke, KNX IP router and KNX IP interface. In addition to the bus voltage the power supply offers an auxiliary voltage.

The KNX IP router in the KNX IP LineMaster 762.1 secure allows forwarding of telegrams between different lines through a LAN (IP) as a fast backbone. Using the embedded KNX IP interface, the KNX line can be connected directly to a PC (e.g. by ETS). The device supports KNX Security which can be enabled in ETS. As secure router the device allows coupling of not secured communication on KNX TP to a secured IP backbone. Also for the interface functionality (unneling) KNX security prevents from unauthorized access. The IP address can be obtained by a DHCP server or by manual configuration (ETS) respectively.

This device works according to the KNXnet/IP specification using the core, the device management, the tunneling and the routing part. The KNX IP LineMaster 762.1 secure has an extended filter table for main groupls 0 to 31 and is able to buffer up to 150 telegrams.

Alimentatore KNX Weinzierl PowerSupply USB 367 – 640mA con Display OLED, Interfaccia USB e Funzioni Logiche.

English description pending.

USB POWER SUPPLY 367 KNX Secure is a 640 mA bus power supply with high efficiency and a small footprint of only 4 units (72 mm). The USB POWER SUPPLY 367 KNX Secure device has a bus choke, an integrated USB interface (Micro USB connector) and additionally provides an output for auxiliary power supply. Via the integrated KNX node USB POWER SUPPLY 367 KNX monitors the output current, the bus voltage and the temperature in the switchgear. The 367 KNX Secure device has various logic functions for application purposes. The configuration of the 367 KNX Secure is done with the ETS (version 4.2 or later). An easy to read OLED display on the front panel allows the user to view the operating parameters locally on the USB POWER SUPPLY 367 KNX Secure. This USB interface can be used to program KNX Secure devices with the ETS.

PD100 KNX presence detector is used in indoor spaces with integrated light sensor to achieve presence detection and constant light functions in a single device.

• Flush or surface mount options
• 6m in diameter movement detection at 2.5 m assembly height
• Integrated light level sensor and movement sensor to achieve constant light function
• Possibility to control air conditioning and ventilation through HVAC
• Adjustable brightness level and duration for “Movement”, “After Movement”, and “No Movement” functions
• Two constant light level adjustments for two states: Vacant & Occupied
• Ability to send movement status periodically with a separate communication object
• Feature to operate as a single sensor when connected with other KNX presence sensors
• Test and calibration modes for convenience during installation
• Does not require an external power supply

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

The KNX USB interface ITR901-003 provides a galvanic isolated bidirectional connection to the bus system via KNX TP and USB. Network configurations become less time-consuming. The device is supplied by both the KNX TP line and USB. No additional external power supply is necessary. 

Download DATASHEET

Presence detector with radio- frequency technology for hidden installation. 360º detection through non-metallic surfaces for installation in technical and false ceilings.Safe against sabotage and non- desired manipulation due to its hidden installation. Suitable for lighting, motion detection, intrusion control, etc.

Kristall offers all the safety and durability advantages of a capacitive keyboard, since there is no mechanical wear of any kind, and ease of use is improved with the introduction of luminous and acoustic feedback.Kristall offers the complete KNX command set needed to control any type of device: On/Off commands, light dimming, window actions and transmission of scenarios.