KNX EnOcean 636 Secure Gateway is a bidirectional gateway between EnOcean wireless devices and the KNX bus. With the KNX EnOcean 636, commands and measured values from wireless EnOcean sensors can be transmitted to the KNX bus. It allows both KNX actuators and EnOcean actuators to be controlled via the KNX bus. The KNX EnOcean 636 Secure Gateway supports encrypted radio communication with security-enabled EnOcean devices. In addition, the Secure Gateway provides control and logic functions and includes a wireless repeater. The KNX EnOcean 636 supports more than 100 profiles with its 32 radio channels. Enables easy and secure connection of various KNX devices and EnOcean sensors and actuators. Commissioning is as simple as usual: With all 32 channels, encryption can be activated individually. Subsequently EnOcean sensors and actuators, which support safety, can be taught in. The user gets more safety without loss of comfort.

USB POWER SUPPLY 367 KNX Secure is a 640 mA bus power supply with high efficiency and a small footprint of only 4 units (72 mm). The USB POWER SUPPLY 367 KNX Secure device has a bus choke, an integrated USB interface (Micro USB connector) and additionally provides an output for auxiliary power supply. Via the integrated KNX node USB POWER SUPPLY 367 KNX monitors the output current, the bus voltage and the temperature in the switchgear. The 367 KNX Secure device has various logic functions for application purposes. The configuration of the 367 KNX Secure is done with the ETS (version 4.2 or later). An easy to read OLED display on the front panel allows the user to view the operating parameters locally on the USB POWER SUPPLY 367 KNX Secure. This USB interface can be used to program KNX Secure devices with the ETS.

640mA BUS Power Supply DGS 366 (AUX 30V) is a high efficiency 640mA bus power supply with a small footprint of only 4 units (72 mm). The 640mA BUS Power Supply DGS 366 (AUX 30V) device has a bus choke and also provides an output for the auxiliary power supply. The integrated KNX node on the 640mA power supply monitors the output current, the bus voltage and the temperature in the switchboard. 640mA BUS Power Supply DGS 366 (AUX 30V) has several logic functions which are available for application purposes. The configuration of BUS DGS is done with the ETS (version 4.2 or later). An easy-to-read front panel OLED display on the DGS BUS allows the user to view operating parameters locally on the device.

• Universal Interface with 4 binary inputs and 4 LED outputs.
• The Universal Interface has 4 channels which can be parameterised as inputs or outputs, e.g. for
  connection of conventional pushbuttons, free-voltage motion detectors, etc.
• The interface can evaluate at its potential-free inputs up to 4 pushbutton/switch states with a
  common reference potential and send the corresponding telegrams.
• The telegrams may be for switching or dimming, blind/shutter control, value transmitter applications
  (light level, temperature,…), light scene control or pulse counting.
• As an alternative, the four channels can control four LEDs as independent outputs.
• The outputs are protected against short circuits, overload and wrong polarity.
• This device is flush mounted in a universal box, behind the pushbutton/switch.
• Dimensions: 38 x 42 x 15mm.
• Programming and commissioning by ETS4 or later.

• Wireless Luminosity sensor transmitter with setpoint temperature value knob for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brightness value and the setpoint value to the lighting actuator.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

The KNX to DALI2 Gateway is a DIN rail module for installation in the distribution board on a 35 mm mounting rail. It is a DALI single-master controller to DALI standard IEC 62386 Parts 101ed2 and 103ed1.The gateway is suitable for use with DALI and DALI-2 systems.It supports Device Type 6, Device Type 8 Tc, Device Type 8 XY coordinate, Device Type 8 RGB with DALI interfaces to IEC 62386 and their integration in a KNX building installation. The DALI gateway has 2 channels DALI output. Up to 64 DALI devices can be connected to each DALI output. DT6 and DT8 devices can all be connected to each DALI output in a mixed configuration. The lamps connected to each DALI channels are controlled via KNX using:broadcast;64 individual lamps;16 lighting groups;16 scenes

• The KNX RF / TP coupler is a compact KNX Radio coupler. Connect the KNX RF devices of a radio line with the KNX Twisted Pair Bus.
• You have a filter table (8k bytes).
• Supports long frames compatible with ETS® ETS5 or higher software.
• The keys on the front allow you to disable the telegram filter for testing purposes.
• The LEDs indicate the operating conditions and communication errors on the KNX bus.
• The power supply is supplied via the KNX bus (main line).
• Programming and commissioning using ETS5 or later.