DINUY RF KNX 2-CHANNEL ON/OFF / 1-CHANNEL BLIND/SHUTTER ACTUATOR

DINUY DINUY RF KNX 2-CHANNEL ON/OFF / 1-CHANNEL...

Wireless 1-channel blind/shutter actuator or 2-channel switching actuator.
Up to 16A switching capacity per channel with 2 free-voltage outputs.
Incorporates RF signal repeater function, which can be enabled or disabled as needed.
Includes 2 auxiliary inputs which allow the local control.
Dimensions: 107 x 53 x 34mm.
230V-operated.
Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 002 & CO KNX 002.

€188.20

DINUY RF KNX Temperature Sensor Probe Heating Floors

DINUY DINUY RF KNX Temperature Sensor Probe...

Wireless Temperature sensor transmitter with Probe for heating floors.
It sends the temperature value in the place where the probe is installed.
Specially-indicated for underfloor heating installations.
Includes the following components:
· Transmitter: captures the value from the temperature probe and transmits it via RF to the linked
receiver.
· Temperature probe: measures the temperature sensed at the tip of the probe. Must be connected
directly to the transmitter via its original cable, which is double insulated. Tip of the probe is
waterproof.
The temperature value is sent every minute.
Incorporates RF signal repeater function, which can be enabled or disabled as needed.
Power supply: 230V~ 50Hz.
Dimensions: 45 x 42 x 12mm.
Radio-frequency: 868,4MHz.
Range: up to 100m (in the free field).
Compatible with: TM KNX 001 & CO KNX 002.

€167.62

DINUY RF KNX WIRELESS BRIGHTNESS SENSOR FOR SOLAR PROTECTION

DINUY DINUY RF KNX WIRELESS BRIGHTNESS SENSOR...

Wireless Luminosity value transmitter for Sun protection function.
It is designed for the automatic control of shutters or blinds.
According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
Luminosity is measured by the sensor attached to the window with a sticker.
Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
Dimensions: 78 x 28 x 23mm.
Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
Radio-frequency: 868,4MHz.
Range: up to 100m (in the free field).
Compatible with: PE KNX 001 & CO KNX 002.

€147.09

DINUY DINUY RF KNX TEMPERATURE SENSOR

Wireless Temperature value transmitter.
Sends the temperature value measured in the place when:
· The temperature value changes more than ±0,5ºC.
· 60 minutes after the last transmission.
· Pressing the inside link key.
Dimensions: 78 x 28 x 23mm.
Portable or wall fix mounted.
Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
Radio-frequency: 868,4MHz.
Range: up to 100m (in the free field).
Compatible with: TM KNX 001 & CO KNX 002.

€123.50

IMI Actuator Thermostatic Valves 160/200 N TA-Slider 160-KNX

IMI Hydronic Engineering IMI Actuator Thermostatic Valves 160/200 N...

Proportional control
Manual override
Stroke detection
Mode, status and position indication
Stroke limitation setting
Valve blockage protection
Valve clogging detection
Error safe position
Diagnostic/Logging
1 binary input, cable 1m

€250.00

Iswitch PI Control LCD 2 Button Plastic Material Variety Color

Interra ISwitch & Pushbuttons Temperature Humidity...

iSwitch is a wall-mounting room controller device for on/off switching of loads, dimming of lighting devices, control of motor drives or other programmable switching and control functions. The product is equipped with integrated temperature sensor, humidity sensor and ambient sensor. iSwitch can act as a room probe or thermostat, both in heating and cooling mode.Body gateway included

€80.00

Bes Thermostat Temperature Control & Humidity Sensor

On sale!

Ingenium* Bes Bes Thermostat Temperature Control &...

Includes PI regulator for controlling temperature with higher accuracy for better energy efciency and comfort
On/Off, PWM or continuous temperature controller for main heat/cool system and additional.
Dew point measurement according to relative humidity and temperature.
Easy Logic Unit.
Available in the White version
Optional Front glass interchangeable, print customizable.

€107.00

D.E AG KNX Fancoil Actuator ANALOG 0-10V or PWM

On sale!

DATEC D.E AG KNX Fancoil Actuator ANALOG 0-10V...

It is device, for Heating or Cooling applications in offices, hotel rooms and much more.The fancoil can be used in Analog 0-10VDC or PWM mode. The fancoil actuator is able to drive up to three fan speeds and an additional 230VAC relay output.The device has two physical inputs, the first for connecting a local temperature sensor and the second to be used as binary input or as window contact input.

€148.50

shop by category

Home Domo Energy

New products

New products

Most View Product

Most View Product

e-Station Smart Ev Home...

E.B® KNX Smart Meter...

Bes Thermostat Temperature...

Contact us

Products

Our company

Soluzioni Integrate

Our privacy policy

1 What are cookies?

2 How we use cookies

3 Controlling Cookies

4 Information We Collect

shop by category

Home Domo Energy  

New products

New products  

Most View Product

Most View Product  

e-Station Smart Ev Home...

E.B® KNX Smart Meter...

Bes Thermostat Temperature...

1 What are cookies?

2 How we use cookies

3 Controlling Cookies

4 Information We Collect

Home Domo Energy

New products

Most View Product