Ingresso Binario KNX DATEC 1630.03160/62100 – 8 Canali da Incasso con 8 LED di Stato.

English description pending.

• Eight completely programmable independent touch areas. 
• Includes a discretized PI regulator to achieve greater comfort and energy savings. 
• Built-in humidity sensor. 
• Dew point measurement according to relative humidity and temperature. 
• Arithmetic Logic Unit 
• Timers/counters.
• Also available in the White version

• The KNX RF / TP coupler is a compact KNX Radio coupler. Connect the KNX RF devices of a radio line with the KNX Twisted Pair Bus.
• You have a filter table (8k bytes).
• Supports long frames compatible with ETS® ETS5 or higher software.
• The keys on the front allow you to disable the telegram filter for testing purposes.
• The LEDs indicate the operating conditions and communication errors on the KNX bus.
• The power supply is supplied via the KNX bus (main line).
• Programming and commissioning using ETS5 or later.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

Basic functionality of the TP line coupler ITR901-002 is coupling two KNX TP lines (main line and subline) providing galvanic isolation in between. Due to its flexibility ITR901-002 coupler unit can be used as KNX line coupler or KNX area coupler (to connect a TP line to a TP area or backbone) or KNX repeater (without filtering). Operational and filtering states, malfunction and faulty communication are indicated by LEDs. 

Download  DATASHEET

Download DATABASE ETS

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless 1-channel Thermostat actuator for HVAC control.
• It incorporates a potentiometer which allows setting the desired temperature avoiding any undesired manipulation.
• Every time it receives a signal of temperature from the sensor it will be compared with the already set in the thermostat and will act accordingly on its relay.
• It also can receive telegrams from door/window contacts or presence detectors.
• Up to 16A switching capacity with free-voltage relay.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Modular installation device. DIN-rail mounting. 1-module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: SE KNX 001, SE KNX 003, SE KNX 004, DP KNX 001 & CO KNX 002.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless Temperature sensor with desired temperature value control knob.
• This sensor sends the following variables:
  · Measured temperature value.
  · Temperature setpoint value.
  · State (Standby or Auto).
• Incorporates a wheel to set the desired temperature in the room.
• Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
• Dimensions: 80 x 30 x 26mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• The Radio Remote Control sends KNX telegrams when one of the keys is presse depending on its parameterisation.
• The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
• Incorporates 5 independent channels, 1 main channel and 5 scene channels.
• Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• The 1-channel Pushbutton sends KNX telegrams when the button is pressed depending on its parameterisation through its switches.
• The device provides functions like switching or dimming of lighting, moving of blinds and shutters,managing scenes,…
• Dimensións: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Switch ON / OFF & Toggle: connects, disconnects or switches the linked actuator. It sends On / OFF / Toggle depending on the configuration.
• Dimmer: connects, disconnects or dims the linked actuator. It sends On / Off / Toggle or Dimming_Up / Dimming_ Down depending on the configuration.
• Blinds / Shutters: controls a linked blind actuator. It sends Step_Up / Step¨_Down or Move_Up / Move_ Down depending on the configuration.
• Scenes: saves and recovers one scene (0…4) depending on the configuration.
• Battery-operated: 2 x 3V Lithium batteries CR2025. Useful life higher than 8 years.
  Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• One channel interface for 2-fold pushbutton.
• Dimmer: Connects, disconnects or dims the linked actuator. It sends ON/OFF or Dimming_Up/Dimming_Down depending on which of the two buttons is pressed the duration of the action.
• Blinds/Shutters: Controls a linked blind actuator. It sends Step_Up/Step_DOwn or Move_Up/Move_Down depending on which of the two buttons is pressed and the duration of the action.
• Scenes: Saves and recovers two different scenes (one scene in each button). It sends Scene_Save or Scene_Load depending on the duration of the action.
• Installaton in standard mechanism box, behind pushbutton.
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX DMS, RE KNX LE1 & RE KNX LE2.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

Attuatore Dimmer LED KNX RF Weinzierl Blue IO 553 CC secure – 4 Uscite Wireless Corrente Costante RGB/RGBW/Tunable White.

English description pending.

The KNX RF BLUE IO 553 CC SECURE is a compact RGB / RGBW / Tunable White dimming actuator with 4 constant current dimming outputs. The dimming actuator KNX RF BLUE IO 553 CC SECURE can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and five LEDs allow a local operation and a visualization of the device state. In addition to the output channels the device includes 16 independent functions for logic or timer control. The KNX RF BLUE IO 553 CC SECURE supports KNX Data Security.

Attuatore Dimmer LED KNX RF Weinzierl Blue IO 552 CV secure – 4 Uscite PWM Wireless RGB/RGBW/Tunable White.

English description pending.

The KNX RF BLUE IO 552 CV SECURE is a compact RGB / RGBW / Tunable White dimming actuator with 4 constant current dimming outputs. The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and five LEDs allow a local operation and a visualization of the device state. In addition to the output channels the KNX RF BLUE IO 552 CV SECURE includes 16 independent functions for logic or timer control. The device supports KNX Data Security.

KNX EnOcean 636 Secure Gateway is a bidirectional gateway between EnOcean wireless devices and the KNX bus. With the KNX EnOcean 636, commands and measured values from wireless EnOcean sensors can be transmitted to the KNX bus. It allows both KNX actuators and EnOcean actuators to be controlled via the KNX bus. The KNX EnOcean 636 Secure Gateway supports encrypted radio communication with security-enabled EnOcean devices. In addition, the Secure Gateway provides control and logic functions and includes a wireless repeater. The KNX EnOcean 636 supports more than 100 profiles with its 32 radio channels. Enables easy and secure connection of various KNX devices and EnOcean sensors and actuators. Commissioning is as simple as usual: With all 32 channels, encryption can be activated individually. Subsequently EnOcean sensors and actuators, which support safety, can be taught in. The user gets more safety without loss of comfort.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

EAE Attuatore Fan Coil FCA100 KNX – Controllo Ventilconvettori 2/4 Tubi, Valvola Triac/0-10V.

English description pending.

EAE Multi Input/Output MIO1616 – 16 Ingressi e 16 Uscite KNX per Pulsanti e Spie.

English description pending.

EAE Accoppiatore di Linea KNX LC200 – Filtro Traffico, Ripetitore, ETS4.2.

English description pending.

EAE Interfaccia IP KNX IPI200 – Tunneling KNXnet/IP, 5 Connessioni Simultanee.

English description pending.

EAE Gateway KNX/Modbus KMG103 640mA – Alimentatore KNX Integrato per Hotel.

English description pending.

EAE Gateway KNX/Modbus KMG103 320mA – Alimentatore KNX Integrato per Hotel.

English description pending.

EAE Alimentatore KNX PS320 – 320mA con Uscita Ausiliaria 30V DC.

English description pending.

EAE KNX Power Supply - 320 mA version. Features an additional 30V DC output, NOT to power an additional KNX bus.

EAE Alimentatore KNX PS640 – 640mA con Uscita Ausiliaria 30V DC.

English description pending.

EAE KNX Power Supply - 640 mA version. Features an additional 30V DC output, NOT to power an additional KNX bus.

EAE IP Router KNX IPR100 – Connessioni KNXnet/IP.

English description pending.

EAE KNX IP router is used as a line or backbone coupler to ensure communication between KNXnet/IP and TP KNX bus line. Electrical insulation is also achieved between the linked lines.

• EAE KNX IP router is a tunneling and routing device. IPR100 is used as a gateway between IP and KNX bus line for commissioning and monitoring purposes. (It is also possible to simultaneously create 4 KNXnet/IP connections).
• Simultaneous connection to two different KNX systems and transmission of telegrams between the local network and different buses
• IP address assignment manually or by DHCP server
• Option to block or allow telegrams between KNX and IP regarding configured filter table
• Deactivation of filter table using on-device buttons for quick diagnosis
• Functional status information with 6 LEDs on device

Download DATASHEET

Download MANUALE PRODOTTO

Download DATABAESE ETS

EAE Interfaccia Universale KNX UI108 – 8 Canali, 6 Modalità Operative.

English description pending.

Colored connection cables

Flush mounted into switch boxes

Does not require an external power supply

8 input channels with each featuring following functions:

• Switching
• Dimming
• Curtain control
• Value and priority
• Scene control
• Pulse counter

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

iSwitch is a wall-mounting room controller device for on/off switching of loads, dimming of lighting devices, control of motor drives or other programmable switching and control functions. The product is equipped with integrated temperature sensor, humidity sensor and ambient sensor. iSwitch can act as a room probe or thermostat, both in heating and cooling mode.Body gateway included

• Wireless 1-channel blind/shutter actuator or 2-channel switching actuator.
• Up to 16A switching capacity per channel with 2 free-voltage outputs.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Includes 2 auxiliary inputs which allow the local control.
• Dimensions: 107 x 53 x 34mm.
• 230V-operated.
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 002 & CO KNX 002.

• Wireless Temperature sensor transmitter with Probe for heating floors.
• It sends the temperature value in the place where the probe is installed.
• Specially-indicated for underfloor heating installations.
• Includes the following components:
  · Transmitter: captures the value from the temperature probe and transmits it via RF to the linked
    receiver.
  · Temperature probe: measures the temperature sensed at the tip of the probe. Must be connected
    directly to the transmitter via its original cable, which is double insulated. Tip of the probe is
    waterproof.
• The temperature value is sent every minute.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Power supply: 230V~ 50Hz.
• Dimensions: 45 x 42 x 12mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Luminosity value transmitter for Sun protection function.
• It is designed for the automatic control of shutters or blinds.
• According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
• Luminosity is measured by the sensor attached to the window with a sticker.
• Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
• Dimensions: 78 x 28 x 23mm.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: PE KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Communication with 8 IP cameras with 8 input and 8 output objects each
• Transfer of the camera events to the KNX bus
• Controlling the camera via the KNX bus
• KNX Bus Terminal and Ethernet / IP Connection (POE)
• Suitable for IP cameras that meet the communication requirements as described in the camera settings in the manual
• Configuration via ETS 5

• Up to 48 telegrams/second routing performance
• Up to 35 telegrams/second tunnelling performance
• Up to five KNXnet/IP tunnel connections
• Integrated display
• 10/100 MBit Ethernet interface
• Power over Ethernet or ext. 16-24 AC or 20-30V DC
• Battery buffered RTC
• SNTP server
• Telnet server

• • Up to 48 telegrams/second routing performance
  • Up to 35 telegrams/second tunnelling performance
  • Up to five KNXnet/IP tunnel connections
  • Integrated display
  • 10/100 MBit Ethernet interface
  • Power over Ethernet or ext. 16-24 AC or 20-30V DC
  • Battery buffered RTC
  • SNTP server
  • Telnet server

voltage input: 230 V AC (50Hz)

output current: 960 mA

Integrated choke

LEDs for operation, bus reset and programming mode

Integrated bus-connection with voltage and current measurement

Data output on KNX bus via group object and visible on display

KNX objects for voltage, current and power measurements

KNX alarm functions

Housing temperature measurement

AUX with 600mA additional output

Alimentatore KNX 640mA DATEC 1630.02150/90100 DIN con Uscita Ausiliaria 30V.

English description pending.

KNX RF USB Interface Stick 340 - Stick USB/KNX RF per Programmazione ETS Wireless e KNX Secure.

English description pending.

 RF USB INTERFACE KNX STICK 340 interface allows establishing a bidirectional connection between a PC or a laptop and the KNX RF wireless network. The device complies with the specification of KNX RF and supports the protocol cEMI. This RF USB INTERFACE KNX STICK 340 can be used to program KNX Secure devices with the ETS. The  RF USB INTERFACE KNX STICK 340 is compatible with ETS 5 (or higher). For software integration (Windows or Linux) of this interface the free SDK kDrive express is available. The power is supplied via the USB port.In addition to the telegram interface via cEMI, the KNX RF USB Interface Stick 340 includes a complete KNX Stack with communication objects and BAOS protocol V2. Thus, the stick offers the possibility to extend devices with USB connection to full KNX devices, which can even be programmed by ETS.

KNX IP LineMaster 762.1 secure - Alimentatore Bus con Router IP e Interfaccia Secure.

English description pending.

The KNX IP LineMaster 762.1 secure combines the essential functions of a KNX bus line: KNX power supply with choke, KNX IP router and KNX IP interface. In addition to the bus voltage the power supply offers an auxiliary voltage.

The KNX IP router in the KNX IP LineMaster 762.1 secure allows forwarding of telegrams between different lines through a LAN (IP) as a fast backbone. Using the embedded KNX IP interface, the KNX line can be connected directly to a PC (e.g. by ETS). The device supports KNX Security which can be enabled in ETS. As secure router the device allows coupling of not secured communication on KNX TP to a secured IP backbone. Also for the interface functionality (unneling) KNX security prevents from unauthorized access. The IP address can be obtained by a DHCP server or by manual configuration (ETS) respectively.

This device works according to the KNXnet/IP specification using the core, the device management, the tunneling and the routing part. The KNX IP LineMaster 762.1 secure has an extended filter table for main groupls 0 to 31 and is able to buffer up to 150 telegrams.

The KNX USB interface ITR901-003 provides a galvanic isolated bidirectional connection to the bus system via KNX TP and USB. Network configurations become less time-consuming. The device is supplied by both the KNX TP line and USB. No additional external power supply is necessary. 

Download DATASHEET

Kristall offers all the safety and durability advantages of a capacitive keyboard, since there is no mechanical wear of any kind, and ease of use is improved with the introduction of luminous and acoustic feedback.Kristall offers the complete KNX command set needed to control any type of device: On/Off commands, light dimming, window actions and transmission of scenarios.