The Blind Actuator KNX IO 520 (1J2I) is a compact blind actuator with two additional binary inputs. The actuator is used to control a blind, a shutter or a window drive. The relay contacts are electrically interlocked. The inputs Blind Actuator KNX IO 520 (1J2I) can be connected to conventional switches with an external voltage of 12 to 230 V. In the not configured state the binary inputs control the actuator channel. Via commissioning the device using ETS® software the binary inputs can be used independently. Two push buttons and three LEDs allow a local operation and a visualization of the device state. In addition to the output and input channels the Blind Actuator KNX IO 520 (1J2I) includes 16 independent functions for logic or timer control.

• ▪ 1 shutter output, 230 V∿, 8 A
• ▪ Drive directions electro-mechanically locked against each other
• ▪ For blinds, shutters or window drives
• ▪ Approach position via time calculation
• ▪ 2 inputs 12..230 V⎓∿, galvanically isolated
• ▪ Switching, dimming, shutters, scenes, pulse counter
• ▪ Integrated logic and timer functions
• ▪ Connections: KNX, plugable screw terminals for IO
• ▪ For DIN rail, width 1 unit (18 mm)

The KNX to DALI2 Gateway is a DIN rail module for installation in the distribution board on a 35 mm mounting rail. It is a DALI single-master controller to DALI standard IEC 62386 Parts 101ed2 and 103ed1.The gateway is suitable for use with DALI and DALI-2 systems.It supports Device Type 6, Device Type 8 Tc, Device Type 8 XY coordinate, Device Type 8 RGB with DALI interfaces to IEC 62386 and their integration in a KNX building installation. The DALI gateway has 2 channels DALI output. Up to 64 DALI devices can be connected to each DALI output. DT6 and DT8 devices can all be connected to each DALI output in a mixed configuration. The lamps connected to each DALI channels are controlled via KNX using:broadcast;64 individual lamps;16 lighting groups;16 scenes

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

Up to 64 DALI devices connectable to DALI Bus (electronic ball st, LED driver, ECK)

Used with EAE DALI Commissioning Tool for DALI operations (addressing, grouping etc.)

16 DALI Groups and 64 different lighting scenes

Each DALI group configurable to function as constant light, corridor or sequence function

Functional and battery life tests for DALI compliant emergency lighting fixtures to be sent through KNX

Monitoring Fault status of DALI devices as different KNX group objects

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE DI INSTALLAZIONE

Download SOFTWARE DALI TOOL

Download DATABASE ETS

Up to 64 DALI devices connectable to DALI Bus (electronic ballast, LED driver, ECK)

Used with EAE DALI Commissioning Tool for DALI operations (addressing, grouping etc.)

16 DALI Groups and 64 different lighting scenes

Each DALI group configurable to function as constant light, corridor or sequence function

Functional and battery life tests for DALI compliant emergency lighting fixtures to be sent through KNX

Monitoring Fault status of DALI devices as different KNX group objects

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE DI INSTALLAZIONE

Download SOFTWARE DALI TOOL

Download DATABASE ETS

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose. 

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose.