The KNX RF BLUE IO 553 CC SECURE is a compact RGB / RGBW / Tunable White dimming actuator with 4 constant current dimming outputs. The dimming actuator KNX RF BLUE IO 553 CC SECURE can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and five LEDs allow a local operation and a visualization of the device state. In addition to the output channels the device includes 16 independent functions for logic or timer control. The KNX RF BLUE IO 553 CC SECURE supports KNX Data Security.

The KNX RF BLUE IO 552 CV SECURE is a compact RGB / RGBW / Tunable White dimming actuator with 4 constant current dimming outputs. The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and five LEDs allow a local operation and a visualization of the device state. In addition to the output channels the KNX RF BLUE IO 552 CV SECURE includes 16 independent functions for logic or timer control. The device supports KNX Data Security.

The KNX TP Blue IO 551 CC secure is a compact RGB / RGBW / Tunable White dimming actuator with 4 constant current dimming outputs. The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and five LEDs allow a local operation and a visualization of the device state. In addition to the output channels the device includes 16 independent functions for logic or timer control. The device supports KNX Data Security.

The KNX TP Blue IO 551 CC secure is a compact RGB / RGBW / Tunable White dimming actuator with 4 constant current dimming outputs. The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and five LEDs allow a local operation and a visualization of the device state. In addition to the output channels the device includes 16 independent functions for logic or timer control. The device supports KNX Data Security.

The KNX RF / ENO Push Button 440 secure unites two wireless protocols in one device: EnOcean and KNX RF. Out of the box the push button operates in EnOcean mode. EnOcean Secure can be enabled via pressing a key combination. By configuration with the ETS® the push button switches to KNX RF mode with optional support of KNX Data Security. Via a factory reset the device can be switched back to EnOcean protocol.

The Blind Actuator KNX IO 520 (1J2I) is a compact blind actuator with two additional binary inputs. The actuator is used to control a blind, a shutter or a window drive. The relay contacts are electrically interlocked. The inputs Blind Actuator KNX IO 520 (1J2I) can be connected to conventional switches with an external voltage of 12 to 230 V. In the not configured state the binary inputs control the actuator channel. Via commissioning the device using ETS® software the binary inputs can be used independently. Two push buttons and three LEDs allow a local operation and a visualization of the device state. In addition to the output and input channels the Blind Actuator KNX IO 520 (1J2I) includes 16 independent functions for logic or timer control.

• ▪ 1 shutter output, 230 V∿, 8 A
• ▪ Drive directions electro-mechanically locked against each other
• ▪ For blinds, shutters or window drives
• ▪ Approach position via time calculation
• ▪ 2 inputs 12..230 V⎓∿, galvanically isolated
• ▪ Switching, dimming, shutters, scenes, pulse counter
• ▪ Integrated logic and timer functions
• ▪ Connections: KNX, plugable screw terminals for IO
• ▪ For DIN rail, width 1 unit (18 mm)

The Universal dimming actuator KNXIO 530 (1D2I) is a compact mains dimmer for 230 V ~ with one output and two binary inputs. The dimming actuator supports phase control or phase section and is thus suitable for all dimmable 230 V lamps (eg incandescent lamps, dimmable LED lamps, halogen lamps). The dimming channel offers various comfort functions, including scenes, automatic, snooze function, staircase lighting and sequencer.The inputs of Universal dimming actuator KNXIO 530 (1D2I) can be controlled via conventional switches with an external voltage of 230 V. In addition to the output and input channels, the Universal dimming actuator KNXIO 530 (1D2I) contains 16 independent logic or timer functions. Two buttons and three LEDs on the front of the device allow local operation and visualization of the device status.

• 2 Regulation channels for LED lighti ng 
• 2 low voltage input (SELV) for pushbutton (non programmable) 
• 8 Programmable scenes executed from bus commands 
• Remote enable / disable of bus control
• Overload circuit protection and thermal protection 
• Digital regulation control based on microcontroller with more than 200 regulation points 
• Last position memory in case of power failure 

The KNX to DALI2 Gateway is a DIN rail module for installation in the distribution board on a 35 mm mounting rail. It is a DALI single-master controller to DALI standard IEC 62386 Parts 101ed2 and 103ed1.The gateway is suitable for use with DALI and DALI-2 systems.It supports Device Type 6, Device Type 8 Tc, Device Type 8 XY coordinate, Device Type 8 RGB with DALI interfaces to IEC 62386 and their integration in a KNX building installation. The DALI gateway has 2 channels DALI output. Up to 64 DALI devices can be connected to each DALI output. DT6 and DT8 devices can all be connected to each DALI output in a mixed configuration. The lamps connected to each DALI channels are controlled via KNX using:broadcast;64 individual lamps;16 lighting groups;16 scenes

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

BX-DM03 is a 4-channels dimmer actuator for LED lamps with current-mode control.The channels can be programmed to work independently with white lamps or can be synchronized to drive the color of a RGB / RGBW lamp.Each channel can be programmed via dip switches to supply the current for the type of lamp installed in accordance with the predetermined standard values: 350mA, 700mA and 1000mA.

Up to 64 DALI devices connectable to DALI Bus (electronic ball st, LED driver, ECK)

Used with EAE DALI Commissioning Tool for DALI operations (addressing, grouping etc.)

16 DALI Groups and 64 different lighting scenes

Each DALI group configurable to function as constant light, corridor or sequence function

Functional and battery life tests for DALI compliant emergency lighting fixtures to be sent through KNX

Monitoring Fault status of DALI devices as different KNX group objects

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE DI INSTALLAZIONE

Download SOFTWARE DALI TOOL

Download DATABASE ETS

Up to 64 DALI devices connectable to DALI Bus (electronic ballast, LED driver, ECK)

Used with EAE DALI Commissioning Tool for DALI operations (addressing, grouping etc.)

16 DALI Groups and 64 different lighting scenes

Each DALI group configurable to function as constant light, corridor or sequence function

Functional and battery life tests for DALI compliant emergency lighting fixtures to be sent through KNX

Monitoring Fault status of DALI devices as different KNX group objects

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE DI INSTALLAZIONE

Download SOFTWARE DALI TOOL

Download DATABASE ETS

It is able to drive a 5 A per channel, 12-24 VDC LED strip – that is a sum of 480 Watt dimming power or 120 Watt for each channel for 24 V LEDs.In device additionally a 16 A switching actuator with two timers is integrated. Thus, the LED power supply is powered on by the actuator if needed or turned off to minimize standby losses of the LED power supply. 

It is able to drive a 5 A per channel, 12-24 VDC LED strip – that is a sum of 480 Watt dimming power or 120 Watt for each channel for 24 V LEDs.In device additionally a 16 A switching actuator with two timers is integrated. Thus, the LED power supply is powered on by the actuator if needed or turned off to minimize standby losses of the LED power supply. 

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose. 

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose. 

• 3 Regulation channels that can be controlled individually or simultaneously 
• Maximum operating output current: 3A per channel
• 8 Programmable scenes executed from bus commands 
• PWM dimming method 
• Overload circuit protection 
• Digital regulation control based on microcontroller more than 200 regulation points 
• Last position with memory in case of power failure

BX-DM02 is a 4-channels dimmer actuator for RGB LED stripes with voltage control.The device works as common anode, and it can drive mainly RGB LED stripes.The module is able to handle 108W at 12V or 216W at 24V.The maximum installed length stripe would be 15 meters 

BX-DM01 is a 4-channels dimmer actuator for white LED stripes with common cathode voltage control, designed to work with the KNX bus. The device is characterized by the possibility of provide very high currents, up to 18A per channel.