• Wireless Temperature sensor transmitter with Probe for heating floors.
• It sends the temperature value in the place where the probe is installed.
• Specially-indicated for underfloor heating installations.
• Includes the following components:
  · Transmitter: captures the value from the temperature probe and transmits it via RF to the linked
    receiver.
  · Temperature probe: measures the temperature sensed at the tip of the probe. Must be connected
    directly to the transmitter via its original cable, which is double insulated. Tip of the probe is
    waterproof.
• The temperature value is sent every minute.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Power supply: 230V~ 50Hz.
• Dimensions: 45 x 42 x 12mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Temperature sensor with desired temperature value control knob.
• This sensor sends the following variables:
  · Measured temperature value.
  · Temperature setpoint value.
  · State (Standby or Auto).
• Incorporates a wheel to set the desired temperature in the room.
• Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
• Dimensions: 80 x 30 x 26mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Luminosity value transmitter for Sun protection function.
• It is designed for the automatic control of shutters or blinds.
• According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
• Luminosity is measured by the sensor attached to the window with a sticker.
• Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
• Dimensions: 78 x 28 x 23mm.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: PE KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• The Radio Remote Control sends KNX telegrams when one of the keys is presse depending on its parameterisation.
• The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
• Incorporates 5 independent channels, 1 main channel and 5 scene channels.
• Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• One channel interface for 2-fold pushbutton.
• Dimmer: Connects, disconnects or dims the linked actuator. It sends ON/OFF or Dimming_Up/Dimming_Down depending on which of the two buttons is pressed the duration of the action.
• Blinds/Shutters: Controls a linked blind actuator. It sends Step_Up/Step_DOwn or Move_Up/Move_Down depending on which of the two buttons is pressed and the duration of the action.
• Scenes: Saves and recovers two different scenes (one scene in each button). It sends Scene_Save or Scene_Load depending on the duration of the action.
• Installaton in standard mechanism box, behind pushbutton.
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX DMS, RE KNX LE1 & RE KNX LE2.

Integrates an indoor Daikin climate unit  with KNX system.Five operating modes (auto, heat, cold,  ventilation and dry). Three fan speeds (low, medium, high). Includes energy saving mode. Arithmetic-logic unit and timers/counters. 

Bi-directional communication gateway between KNX protocol and Fermax Smile Dominium video intercom.Allows to control and manage KNX devices from the Smile Dominium video intercom, using a project uploaded from the SiDEKNX software.Direct connection to the Fermax Smile Dominium video entry system and the KNX bus.  

It is possible to adjust the presence sensor sensitivity in an easy way,selecting between 3 different levels or personalizing by yourself.It includes parameters to define regulation steps,to establish deviations, or to calibrate it.It is also possible to change between auto and manual mode, defining the behavior when it changes between those two options.It also includes an additional thermostat 

• 3 Regulation channels that can be controlled individually or simultaneously 
• Maximum operating output current: 3A per channel
• 8 Programmable scenes executed from bus commands 
• PWM dimming method 
• Overload circuit protection 
• Digital regulation control based on microcontroller more than 200 regulation points 
• Last position with memory in case of power failure

Capacitive push-button with 4 independent touch areas, completely programmable.LED indicator associated with each touch areas. Square format. Universal distribution box size. In-built temperature sensor to measure and to send the information to KNX BUS. 

• Supply: 29V DC from KNX BUS
• Size: 88 x 88 x 8mm
• Mounted on universal box, screwed on wall

The panel has been designed to show all controls on a single page including 8 (up to 32 into 4 pages). It also includes a specific interface for climate control with an internal thermostat. The ability of the panel to generate a wifi network to allow it to be controlled locally from any iOS or Android device, simply by downloading the official Ingenium applications.