• The 4-channels Analog/Digital interface is equipped with 4 independent channels which may be used as inputs for Analog or Digital signals.
• Each channel may be used depending on the parameterization by the ETS:
  • Binary input: the interface can evaluate at its potential-free inputs up to 4 pushbutton/switch states and send the corresponding telegram according to the configured setting as: Switch, Dimmer, Multiple Switch, Sequential Switch, Shutter/Blind control, Scene Control, Fixed/Forced value or Counter.
  • Analogue input: temperature sensor by connecting an external temperature probe (ST KNT 001 or ST KNT 002).
• Can be configured and enabled up to 4 independent Thermostats.
• Flush-mounting within universal box, behind the pushbutton/switch.
• The inputs are protected against short-circuit, overload and wrong polarity.
• Supply from the Bus. External supply is not required.
• Built-in KNX BCU (Bus Coupler Unit).
• Programming and commissioning by ETS4 or later.

• Wireless wall-mounted Infrared PIR motion detector for lighting control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• As soon as it detects movement, the sensor sends the ON signal to the linked receiver and its
  contact keeps closed. The ON time must be set on the receiver.
• Wall or ceiling mounting installation.
• Coverage: 180º and Ø10m at 2m high.
• Power Supply: 2 x 3V AA Lithium batteries L91. Working life over 15 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: IT KNX 001, MI KNX 001 & CO KNX 002.

• Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• It has 2 operation modes:
  · Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 & CO KNX 002.
  · Presence detector: useful for heating and air conditioning control.
• Compatible with the actuators: TM KNX 001 & CO KNX 002.
• Incorporates Temperature sensor
• Coverage: 360º and Ø7m at 2,5m high.
• Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
• Radio-frequency: 868,4MHz.

• Wireless Luminosity sensor transmitter for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brigthness value to the lighting actuator for constant light control operation.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

• Wireless Temperature sensor transmitter with Probe for heating floors.
• It sends the temperature value in the place where the probe is installed.
• Specially-indicated for underfloor heating installations.
• Includes the following components:
  · Transmitter: captures the value from the temperature probe and transmits it via RF to the linked
    receiver.
  · Temperature probe: measures the temperature sensed at the tip of the probe. Must be connected
    directly to the transmitter via its original cable, which is double insulated. Tip of the probe is
    waterproof.
• The temperature value is sent every minute.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Power supply: 230V~ 50Hz.
• Dimensions: 45 x 42 x 12mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Temperature sensor with desired temperature value control knob.
• This sensor sends the following variables:
  · Measured temperature value.
  · Temperature setpoint value.
  · State (Standby or Auto).
• Incorporates a wheel to set the desired temperature in the room.
• Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
• Dimensions: 80 x 30 x 26mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Luminosity value transmitter for Sun protection function.
• It is designed for the automatic control of shutters or blinds.
• According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
• Luminosity is measured by the sensor attached to the window with a sticker.
• Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
• Dimensions: 78 x 28 x 23mm.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: PE KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• The Radio Remote Control sends KNX telegrams when one of the keys is presse depending on its parameterisation.
• The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
• Incorporates 5 independent channels, 1 main channel and 5 scene channels.
• Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• One channel interface for 2-fold pushbutton.
• Dimmer: Connects, disconnects or dims the linked actuator. It sends ON/OFF or Dimming_Up/Dimming_Down depending on which of the two buttons is pressed the duration of the action.
• Blinds/Shutters: Controls a linked blind actuator. It sends Step_Up/Step_DOwn or Move_Up/Move_Down depending on which of the two buttons is pressed and the duration of the action.
• Scenes: Saves and recovers two different scenes (one scene in each button). It sends Scene_Save or Scene_Load depending on the duration of the action.
• Installaton in standard mechanism box, behind pushbutton.
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX DMS, RE KNX LE1 & RE KNX LE2.

• Capacitive touch sensor for up to 25mm material size
• Three sensor panels enable button, double-click and wiping-gesture (acustic feedback customizable)
• Sensor panels can be used as one big panel
• Up to six switching options (acustic feedback customizable)
• Plastic housing (210x140x11 mm) robust against splash water
• Reset time programmable by switching timer
• KNX-Bus power required only

It is able to drive a 5 A per channel, 12-24 VDC LED strip – that is a sum of 480 Watt dimming power or 120 Watt for each channel for 24 V LEDs.In device additionally a 16 A switching actuator with two timers is integrated. Thus, the LED power supply is powered on by the actuator if needed or turned off to minimize standby losses of the LED power supply.