The Sensor On-Off Dim Up-Down KNX MicroWave is a dual technology infrared and microwave sensor. The sensor is used to detect the presence of moving people. It is possible to set the operation of the Sensor On-Off Dim Up-Down KNX or infrared only, microwave or both. It is also equipped with a brightness sensor with the possibility of setting the light source: internal, external. In the Sensor On-Off Dim Up-Down KNX the brightness function can be used alone or in combination with the detection function.When the brightness sensor is combined with detection it will be necessary that the requirements of both settings are met. The use of the sensor is suitable for residential, commercial and tertiary environments.

• The KNX RF / TP coupler is a compact KNX Radio coupler. Connect the KNX RF devices of a radio line with the KNX Twisted Pair Bus.
• You have a filter table (8k bytes).
• Supports long frames compatible with ETS® ETS5 or higher software.
• The keys on the front allow you to disable the telegram filter for testing purposes.
• The LEDs indicate the operating conditions and communication errors on the KNX bus.
• The power supply is supplied via the KNX bus (main line).
• Programming and commissioning using ETS5 or later.

Attuatore KNX Motor Control DATEC 1630.03141/65100 – Comando Ventilatore a Soffitto da Incasso 230VAC 100W.

English description pending.

The Enertex® LED PowerSupply 160W/48V supplies LED strips and DC loads with 48V DC at 160W. Ideal for long cable runs. DIN rail, parallel capable, self-healing protections.

The Enertex® LED PowerSupply 160W/24V supplies LED strips and DC loads with 24V DC at 160W. DIN rail, parallel capable, self-healing protections. Optimized for Enertex KNX LED dimmers.

The Enertex® LED PowerSupply 160W/12V supplies LED strips and DC loads with 12V DC at 160W. DIN rail, parallel capable, self-healing protections. Optimized for Enertex KNX LED dimmers.

Triple cover frame in white RAL9010 powder-coated aluminium for three adjacent Enertex MeTa KNX room controllers.

Triple cover frame in black anodized aluminium for three adjacent Enertex MeTa KNX room controllers.

Triple cover frame in natural brushed aluminium for three adjacent Enertex MeTa KNX room controllers.

Double cover frame in black anodized aluminium for two adjacent Enertex MeTa KNX room controllers.

Double cover frame in white RAL9010 powder-coated aluminium for two adjacent Enertex MeTa KNX room controllers.

Double cover frame in natural brushed aluminium for two adjacent Enertex MeTa KNX room controllers. Fits JUNG A and AS 500 series inserts.

Single cover frame in white RAL9010 powder-coated aluminium for Enertex MeTa KNX room controller. Fits JUNG A and AS 500 series inserts.

Single cover frame in black anodized aluminium for Enertex MeTa KNX room controller. Fits JUNG A and AS 500 series inserts.

Single cover frame in natural brushed anodized aluminium for Enertex MeTa KNX room controller. Fits JUNG A and AS 500 series inserts.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

Basic functionality of the TP line coupler ITR901-002 is coupling two KNX TP lines (main line and subline) providing galvanic isolation in between. Due to its flexibility ITR901-002 coupler unit can be used as KNX line coupler or KNX area coupler (to connect a TP line to a TP area or backbone) or KNX repeater (without filtering). Operational and filtering states, malfunction and faulty communication are indicated by LEDs. 

Download  DATASHEET

Download DATABASE ETS

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless 1-channel Thermostat actuator for HVAC control.
• It incorporates a potentiometer which allows setting the desired temperature avoiding any undesired manipulation.
• Every time it receives a signal of temperature from the sensor it will be compared with the already set in the thermostat and will act accordingly on its relay.
• It also can receive telegrams from door/window contacts or presence detectors.
• Up to 16A switching capacity with free-voltage relay.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Modular installation device. DIN-rail mounting. 1-module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: SE KNX 001, SE KNX 003, SE KNX 004, DP KNX 001 & CO KNX 002.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless wall-mounted Infrared PIR motion detector for lighting control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• As soon as it detects movement, the sensor sends the ON signal to the linked receiver and its
  contact keeps closed. The ON time must be set on the receiver.
• Wall or ceiling mounting installation.
• Coverage: 180º and Ø10m at 2m high.
• Power Supply: 2 x 3V AA Lithium batteries L91. Working life over 15 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: IT KNX 001, MI KNX 001 & CO KNX 002.

• Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• It has 2 operation modes:
  · Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 & CO KNX 002.
  · Presence detector: useful for heating and air conditioning control.
• Compatible with the actuators: TM KNX 001 & CO KNX 002.
• Incorporates Temperature sensor
• Coverage: 360º and Ø7m at 2,5m high.
• Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
• Radio-frequency: 868,4MHz.

• Wireless Luminosity sensor transmitter for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brigthness value to the lighting actuator for constant light control operation.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

• Wireless Temperature sensor with desired temperature value control knob.
• This sensor sends the following variables:
  · Measured temperature value.
  · Temperature setpoint value.
  · State (Standby or Auto).
• Incorporates a wheel to set the desired temperature in the room.
• Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
• Dimensions: 80 x 30 x 26mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• The Radio Remote Control sends KNX telegrams when one of the keys is presse depending on its parameterisation.
• The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
• Incorporates 5 independent channels, 1 main channel and 5 scene channels.
• Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• The 1-channel Pushbutton sends KNX telegrams when the button is pressed depending on its parameterisation through its switches.
• The device provides functions like switching or dimming of lighting, moving of blinds and shutters,managing scenes,…
• Dimensións: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Switch ON / OFF & Toggle: connects, disconnects or switches the linked actuator. It sends On / OFF / Toggle depending on the configuration.
• Dimmer: connects, disconnects or dims the linked actuator. It sends On / Off / Toggle or Dimming_Up / Dimming_ Down depending on the configuration.
• Blinds / Shutters: controls a linked blind actuator. It sends Step_Up / Step¨_Down or Move_Up / Move_ Down depending on the configuration.
• Scenes: saves and recovers one scene (0…4) depending on the configuration.
• Battery-operated: 2 x 3V Lithium batteries CR2025. Useful life higher than 8 years.
  Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• One channel interface for 2-fold pushbutton.
• Dimmer: Connects, disconnects or dims the linked actuator. It sends ON/OFF or Dimming_Up/Dimming_Down depending on which of the two buttons is pressed the duration of the action.
• Blinds/Shutters: Controls a linked blind actuator. It sends Step_Up/Step_DOwn or Move_Up/Move_Down depending on which of the two buttons is pressed and the duration of the action.
• Scenes: Saves and recovers two different scenes (one scene in each button). It sends Scene_Save or Scene_Load depending on the duration of the action.
• Installaton in standard mechanism box, behind pushbutton.
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX DMS, RE KNX LE1 & RE KNX LE2.

High-frequency motion detector HF 3360, ideal for basement corridors, stairwells, multi-storey car parks, installation height 2.8 m, 360° angle of coverage, reach 1 – 8 m (radial), detection regardless of temperature, HF-sensor technology also detects movement through glass, wood and stud walls. 

Infrared presence detector Presence Control PRO IR Quattro HD KNX for indoors, ideal for medium to large-size offices, conference and meeting rooms, classrooms and lecture theatres, sports halls and warehouses,installation height up to 10 m,controll 4 lighting channels and HVAC,4800 switching zones for the ultimate in detection quality, presence detection over a true 64 m2, square detection zone. 

IS 3360 MX Highbay motion detector – ideal for high ceilings in industrial buildings or commercial properties. For mounting heights of up to 14 m. High-precision 360° infrared sensor. Maximum reach: 18 m. For watching over up to 1000 sq.m  

IS 3360 MX Highbay motion detector – ideal for high ceilings in industrial buildings or commercial properties. For mounting heights of up to 14 m. High-precision 360° infrared sensor. Maximum reach: 18 m. For watching over up to 1000 sq.m 

It is possible to adjust the presence sensor sensitivity in an easy way,selecting between 3 different levels or personalizing by yourself.It includes parameters to define regulation steps,to establish deviations, or to calibrate it.It is also possible to change between auto and manual mode, defining the behavior when it changes between those two options.It also includes an additional thermostat 

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.

English description pending.