• Universal Interface with 4 binary inputs and 4 LED outputs.
• The Universal Interface has 4 channels which can be parameterised as inputs or outputs, e.g. for
  connection of conventional pushbuttons, free-voltage motion detectors, etc.
• The interface can evaluate at its potential-free inputs up to 4 pushbutton/switch states with a
  common reference potential and send the corresponding telegrams.
• The telegrams may be for switching or dimming, blind/shutter control, value transmitter applications
  (light level, temperature,…), light scene control or pulse counting.
• As an alternative, the four channels can control four LEDs as independent outputs.
• The outputs are protected against short circuits, overload and wrong polarity.
• This device is flush mounted in a universal box, behind the pushbutton/switch.
• Dimensions: 38 x 42 x 15mm.
• Programming and commissioning by ETS4 or later.

Ingresso Binario KNX DATEC 1630.03160/62100 – 8 Canali da Incasso con 8 LED di Stato.

English description pending.

Attuatore di Commutazione KNX DATEC 1630.03160/61100 – 4 Canali 10A da Incasso con Ingressi Binari.

English description pending.

• Wireless Luminosity sensor transmitter with setpoint temperature value knob for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brightness value and the setpoint value to the lighting actuator.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

• Eight completely programmable independent touch areas. 
• Includes a discretized PI regulator to achieve greater comfort and energy savings. 
• Built-in humidity sensor. 
• Dew point measurement according to relative humidity and temperature. 
• Arithmetic Logic Unit 
• Timers/counters.
• Also available in the White version

A 12 channel KNX actuatorfor monitoring electrical loads with outputs up to 16A.  The device provides the traditional switching functions, complete with notification of the state, stop command, timer functions and scenarios. It also has a set of logical functions consisting of 16 freely configurable communications objects (OR, AND, XOR). The outputs can be pre-set individually by ETS.  

A 8 channel KNX actuatorfor monitoring electrical loads with outputs up to 16A.  The device provides the traditional switching functions, complete with notification of the state, stop command, timer functions and scenarios. It also has a set of logical functions consisting of 16 freely configurable communications objects (OR, AND, XOR). The outputs can be pre-set individually by ETS.  

A 4 channel KNX actuatorfor monitoring electrical loads with outputs up to 16A.  The device provides the traditional switching functions, complete with notification of the state, stop command, timer functions and scenarios. It also has a set of logical functions consisting of 16 freely configurable communications objects (OR, AND, XOR). The outputs can be pre-set individually by ETS.  

• Temperature sensor 0 to 51 ° C
• Temperature Controller: 2 points, or continuous PWM
• PI control algorithm
• Control system hot / main heat output and additional on/off
• Flush mounting in box with vented cap mechanism
• Simple logic unit  

• The KNX RF / TP coupler is a compact KNX Radio coupler. Connect the KNX RF devices of a radio line with the KNX Twisted Pair Bus.
• You have a filter table (8k bytes).
• Supports long frames compatible with ETS® ETS5 or higher software.
• The keys on the front allow you to disable the telegram filter for testing purposes.
• The LEDs indicate the operating conditions and communication errors on the KNX bus.
• The power supply is supplied via the KNX bus (main line).
• Programming and commissioning using ETS5 or later.

• 2 Regulation channels for LED lighti ng 
• 2 low voltage input (SELV) for pushbutton (non programmable) 
• 8 Programmable scenes executed from bus commands 
• Remote enable / disable of bus control
• Overload circuit protection and thermal protection 
• Digital regulation control based on microcontroller with more than 200 regulation points 
• Last position memory in case of power failure 

The panel has been designed to show all controls on a single page including 8 (up to 32 into 4 pages). It also includes a specific interface for climate control with an internal thermostat. The ability of the panel to generate a wifi network to allow it to be controlled locally from any iOS or Android device, simply by downloading the official Ingenium applications. 

Attuatore KNX Fancoil DATEC 1630.02120/55100 – Singola Valvola Riscaldamento/Raffrescamento Analogica o PWM DIN.

English description pending.

Attuatore KNX Motor Control DATEC 1630.03141/65100 – Comando Ventilatore a Soffitto da Incasso 230VAC 100W.

English description pending.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

Basic functionality of the TP line coupler ITR901-002 is coupling two KNX TP lines (main line and subline) providing galvanic isolation in between. Due to its flexibility ITR901-002 coupler unit can be used as KNX line coupler or KNX area coupler (to connect a TP line to a TP area or backbone) or KNX repeater (without filtering). Operational and filtering states, malfunction and faulty communication are indicated by LEDs. 

Download  DATASHEET

Download DATABASE ETS

EAE Room Control Unit RCU2018 – 20 Uscite 16A, 18 Ingressi KNX.

English description pending.

EAE Room Control Unit RCU2018 – 20 Uscite 16A, 18 Ingressi KNX.

English description pending.

Room Control Unit covers all requirements of the electrical installation of room applications and offers following functions in a one product.

• Switching lighting
• Switching loads
• Controlling AC/DC blinds
• Controlling fan coils (2 & 3 point valve)
• Dry contact inputs

Suitable for switching resistive, capacitive and inductive loads as well as fluorescent lamp loads according to EN 60 669. As a switch output device provides following function list:

• Staircase
• External logic
• Internal logic 
• Priority
• Threshold
• Operating hour
• Sweep

Input channel operates as universal interface with following functions :

• Switch / push button input 
• Dimmer control 
• Control of shutter/blinds 
• Value sending 
• Scene control 
• Counter for count pulse

Download DATASHEET

Download DATABASE ETS

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless 1-channel Thermostat actuator for HVAC control.
• It incorporates a potentiometer which allows setting the desired temperature avoiding any undesired manipulation.
• Every time it receives a signal of temperature from the sensor it will be compared with the already set in the thermostat and will act accordingly on its relay.
• It also can receive telegrams from door/window contacts or presence detectors.
• Up to 16A switching capacity with free-voltage relay.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Modular installation device. DIN-rail mounting. 1-module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: SE KNX 001, SE KNX 003, SE KNX 004, DP KNX 001 & CO KNX 002.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless wall-mounted Infrared PIR motion detector for lighting control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• As soon as it detects movement, the sensor sends the ON signal to the linked receiver and its
  contact keeps closed. The ON time must be set on the receiver.
• Wall or ceiling mounting installation.
• Coverage: 180º and Ø10m at 2m high.
• Power Supply: 2 x 3V AA Lithium batteries L91. Working life over 15 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: IT KNX 001, MI KNX 001 & CO KNX 002.

• Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• It has 2 operation modes:
  · Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 & CO KNX 002.
  · Presence detector: useful for heating and air conditioning control.
• Compatible with the actuators: TM KNX 001 & CO KNX 002.
• Incorporates Temperature sensor
• Coverage: 360º and Ø7m at 2,5m high.
• Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
• Radio-frequency: 868,4MHz.

• Wireless Luminosity sensor transmitter for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brigthness value to the lighting actuator for constant light control operation.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

• Wireless Temperature sensor with desired temperature value control knob.
• This sensor sends the following variables:
  · Measured temperature value.
  · Temperature setpoint value.
  · State (Standby or Auto).
• Incorporates a wheel to set the desired temperature in the room.
• Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
• Dimensions: 80 x 30 x 26mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• The Radio Remote Control sends KNX telegrams when one of the keys is presse depending on its parameterisation.
• The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
• Incorporates 5 independent channels, 1 main channel and 5 scene channels.
• Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• One channel interface for 2-fold pushbutton.
• Dimmer: Connects, disconnects or dims the linked actuator. It sends ON/OFF or Dimming_Up/Dimming_Down depending on which of the two buttons is pressed the duration of the action.
• Blinds/Shutters: Controls a linked blind actuator. It sends Step_Up/Step_DOwn or Move_Up/Move_Down depending on which of the two buttons is pressed and the duration of the action.
• Scenes: Saves and recovers two different scenes (one scene in each button). It sends Scene_Save or Scene_Load depending on the duration of the action.
• Installaton in standard mechanism box, behind pushbutton.
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX DMS, RE KNX LE1 & RE KNX LE2.

Integrates an indoor Daikin climate unit  with KNX system.Five operating modes (auto, heat, cold,  ventilation and dry). Three fan speeds (low, medium, high). Includes energy saving mode. Arithmetic-logic unit and timers/counters. 

Bi-directional communication gateway between KNX protocol and Fermax Smile Dominium video intercom.Allows to control and manage KNX devices from the Smile Dominium video intercom, using a project uploaded from the SiDEKNX software.Direct connection to the Fermax Smile Dominium video entry system and the KNX bus.  

It is possible to adjust the presence sensor sensitivity in an easy way,selecting between 3 different levels or personalizing by yourself.It includes parameters to define regulation steps,to establish deviations, or to calibrate it.It is also possible to change between auto and manual mode, defining the behavior when it changes between those two options.It also includes an additional thermostat 

Capacitive push-button with 4 independent touch areas, completely programmable.LED indicator associated with each touch areas. Square format. Universal distribution box size. In-built temperature sensor to measure and to send the information to KNX BUS. 

• Supply: 29V DC from KNX BUS
• Size: 88 x 88 x 8mm
• Mounted on universal box, screwed on wall

The webserver all

ows to control a KNX installation using an iOS, Android or Samsung Smart TV devices remotely through the Ingenium server or a PC connected to the internet with any type of web browser. This webserver has Wi-Fi connectivity and 1 Ethernet port (10 Mbit/sec). The control applications are completely free.  

Download IL DATASHEET

Download IL MANUALE

Download IL SOFTWARE 

Power Supply KNX max Current 320mA. Input Voltage 230/110 VAC – 50/60Hz.

Dimmer KNX LED a Corrente Blumotix BX-DM03 – 4 Canali RGB/RGBW, Anodo Comune, 350/700/1000mA.

English description pending.

BX-2XIO is a 4-channels push button interface used to acquire external commands.This is the new push-button interface equipped with outputs for monitoring the warning LEDs found in modern domestic series. .The device provides control functions for load control, the opening and closing of shutters, the adjustment of a light source and the selection of scenarios. 

Attuatore Multifunzione KNX Blumotix BX-MFB12 – 12 Canali 16A DIN.

English description pending.

A KNX device for measuring Alternating Electrical Current. This device measures the alternating current absorbed on an electrical line and indirectly provides the power values that can be used to determine the amount of electrical power consumed.The 3 channels can be programmed independently by ETS to carry out energy saving operations. Current clamps not included 

Kristall offers all the safety and durability advantages of a capacitive keyboard, since there is no mechanical wear of any kind, and ease of use is improved with the introduction of luminous and acoustic feedback.Kristall offers the complete KNX command set needed to control any type of device: On/Off commands, light dimming, window actions and transmission of scenarios.

Kristall offers all the safety and durability advantages of a capacitive keyboard, since there is no mechanical wear of any kind, and ease of use is improved with the introduction of luminous and acoustic feedback.Kristall offers the complete KNX command set needed to control any type of device: On/Off commands, light dimming, window actions and transmission of scenarios.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

Thinka for KNX allows you control your home with Siri and Alexa.

Thinka allows you to manage your lights, switches, curtains, (Venetian) blinds and climate control. And it reads sensors such as temperature, humidity, CO2, motion, contact and occupancy.

You can use Apple's Home App on your iPhone or iPad to switch on lights, close the curtains or turn up the heat. Or do it all at once with HomeKit scenes. And share with all people in your household.

The Thinka is typically installed on the DIN-rail, connected to KNX via twisted pair, Ethernet and power. 

Scarica MANUALE 

Video    INSTALLAZIONE

Video    PROGRAMMAZIONE

EAE Oria Termostato KNX LCD 4 Pulsanti INT-OT4.

English description pending.

Oria thermostats are offered in three different colour s: Pearl White, Mustang gray and Anthracite.

Monitoring climate via digital LCD

Internal temperature sensor (°C/ °F)

Adjustable fan speed (1, 2, 3, Automatic)

Multiple operation modes (Comfort, Night, Outdoor, Indoor)

Fully automatic operation feature (hot-cold transition)

Ability to control different HVAC units including VRF-VRV

PI relative, PI on-off (PWM), On/Off, Fan coil, Split unit

Installation ability to 60x60 mm standard switch junctions

4 dependent or 8 independent programmable buttons for various functions:

• Switching
• Dimming
• Shutter/Blind control
• Value and priority assignment
• Scene control
• Status notification LEDs

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

EAE Oria Termostato KNX LCD 3 Pulsanti INT-OT3.

English description pending.

Oria thermostats are offered in three different colour s: Pearl White, Mustang gray and Anthracite.

Monitoring climate via digital LCD

Internal temperature sensor (°C/ °F)

Adjustable fan speed (1, 2, 3, Automatic)

Multiple operation modes (Comfort, Night, Outdoor, Indoor)

Fully automatic operation feature (hot-cold transition)

Ability to control different HVAC units including VRF-VRV

PI relative, PI on-off (PWM), On/Off, Fan coil, Split unit

Installation ability to 60x60 mm standard switch junctions

3 dependent or 6 independent programmable buttons for various functions:

• Switching
• Dimming
• Shutter/Blind control
• Value and priority assignment
• Scene control
• Status notification LEDs

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

EAE Oria Termostato KNX LCD 2 Pulsanti INT-OT2.

English description pending.

Oria thermostats are offered in three different colours: Pearl White, Mustang gray and Anthracite.

Monitoring climate via digital LCD

Internal temperature sensor (°C/ °F)

Adjustable fan speed (1, 2, 3, Automatic)

Multiple operation modes (Comfort, Night, Outdoor, Indoor)

Fully automatic operation feature (hot-cold transition)

Ability to control different HVAC units including VRF-VRV

PI relative, PI on-off (PWM), On/Off, Fan coil, Split unit

Installation ability to 60x60 mm standard switch junctions

2 dependent or 4 independent programmable buttons for various functions:

• Switching
• Dimming
• Shutter/Blind control
• Value and priority assignment
• Scene control
• Status notification LEDs

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

EAE Alimentatore KNX PS320 – 320mA con Uscita Ausiliaria 30V DC.

English description pending.

EAE KNX Power Supply - 320 mA version. Features an additional 30V DC output, NOT to power an additional KNX bus.

EAE Alimentatore KNX PS640 – 640mA con Uscita Ausiliaria 30V DC.

English description pending.

EAE KNX Power Supply - 640 mA version. Features an additional 30V DC output, NOT to power an additional KNX bus.

MD100 KNX movement detector is used in indoor spaces with integrated light sensor to achieve presence detection and constant light functions in a single device.

• Flush or surface mount options
• 9m in diameter movement detection at 2.5 m assembly height
• Integrated light level sensor and movement sensor to achieve constant light function
• Possibility to control air conditioning and ventilation through HVAC
• Adjustable brightness level and duration for “Movement”, “After Movement”, and “No Movement” functions
• Two constant light level adjustments for two states: Vacant & Occupied
• Ability to send movement status periodically with a separate communication object
• Feature to operate as a single sensor when connected with other KNX presence sensors
• Test and calibration modes for convenience during installation
• Does not require an external power supply

Download DATASHEET

Download MANUALE PRODOTTO

Download MANUALE INSTALLAZIONE

Download DATABASE ETS

EAE IP Router KNX IPR100 – Connessioni KNXnet/IP.

English description pending.

EAE KNX IP router is used as a line or backbone coupler to ensure communication between KNXnet/IP and TP KNX bus line. Electrical insulation is also achieved between the linked lines.

• EAE KNX IP router is a tunneling and routing device. IPR100 is used as a gateway between IP and KNX bus line for commissioning and monitoring purposes. (It is also possible to simultaneously create 4 KNXnet/IP connections).
• Simultaneous connection to two different KNX systems and transmission of telegrams between the local network and different buses
• IP address assignment manually or by DHCP server
• Option to block or allow telegrams between KNX and IP regarding configured filter table
• Deactivation of filter table using on-device buttons for quick diagnosis
• Functional status information with 6 LEDs on device

Download DATASHEET

Download MANUALE PRODOTTO

Download DATABAESE ETS