iSwitch is a wall-mounting room controller device for on/off switching of loads, dimming of lighting devices, control of motor drives or other programmable switching and control functions. The product is equipped with integrated temperature sensor, humidity sensor and ambient sensor. iSwitch can act as a room probe or thermostat, both in heating and cooling mode.Body gateway included

Attuatore commutazione/tapparelle 2 uscite e 4 ingressi Dinuy PE K5X 001.

English description pending.

Interfaccia KNX Dinuy EM KNT 002 a 4 Canali Ingressi Binari/Analogici.

English description pending.

Sensore temperatura con sonda Dinuy SE K5X 005.

English description pending.

Attuatore dimmer per strisce LED Dinuy RE K5X LE2.

English description pending.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

Infrared motion detector IS 345 MX Highbay for indoors, ideal for large heights in depots, high-bay warehouses, machine shops, check-in areas and departure lounges, installation height 14 m, detection zone 30 x 4 m (radial), large terminal compartment for easy installation. Available as square surface-mounted and concealed version.  

BX-TU is the innovative push button interface equipped with an external temperature and humidiy probe to perform thermostat functions, humidy and dew point temperature control.The device is developed without a display unit or local buttons, therefore, setpoint temperature adjustment and visualization can be exclusively carried out via a Blumotix supervision system.

• Aluminum housing 
• Display: 4.3inch TFT with advanced GUI 
• Working voltage: DC 24V (support POE ) 
• Card Supported: IC/ID card 
• Support intercommunication function 
• Support tamper alarm
• IPX4 waterproof    

• Detection of air quality
  (CO2-concentration, rel. humidity, temperature)
• CO2-sensor (Measuring range 390–10.000 ppm)
• CO2-value is atmospheric pressure compensated
• Sensors for CO2-, temperature, humidity and atmospheric pressure measurement
• Humidity sensor (Measuring range 0...100% rel. humidity)
• Temperature sensor (Measuring range 0°/50°C)
• 5 binary and analogue inputs

• Daily, weekly and yearly program
• 10 years battery-reserve
• Up to 300 permanent switchings by date
• Manual permanent mode
• Automatic sorting of switching times on readout
• Fully automatic daylight saving time
• Elapsed time and pulse counter
• Pulse function
• Cycle function
• Timer function
• Channel button function
• DCF function
• Security by PIN-Code
• Illuminated display
• Data-key function

• Two-point ON / OFF control
• Shutter Control (Heat Shut Off contact)
• Motion detector (intrusion)
• Thermoregulation with radiator control
• Remote Control (Optional)

• Proportional control
• Manual override
• Stroke detection
• Mode, status and position indication
• Stroke limitation setting
• Valve blockage protection
• Valve clogging detection
• Error safe position
• Diagnostic/Logging
• 1 binary input, cable 1m 

• Communication with 8 IP cameras with 8 input and 8 output objects each
• Transfer of the camera events to the KNX bus
• Controlling the camera via the KNX bus
• KNX Bus Terminal and Ethernet / IP Connection (POE)
• Suitable for IP cameras that meet the communication requirements as described in the camera settings in the manual
• Configuration via ETS 5

SynOhr® MultiSense KNX Premium:

• MultiSense KNX Standard command
• Self-sufficient Speech Recognition with 40 commands
• Speech recognition wildcard commands
• Monitoring of noise levels (as a baby monitor)
• Display of 28 characters with auto-scrolling on the dot matrix
• Use of the dot matrix on the display of icons
• Different Effects for the Ring and Ambient lightning
• Master/slave mode 

• Capacitive touch sensor for up to 25mm material size
• Three sensor panels enable button, double-click and wiping-gesture (acustic feedback customizable)
• Sensor panels can be used as one big panel
• Up to six switching options (acustic feedback customizable)
• Plastic housing (210x140x11 mm) robust against splash water
• Reset time programmable by switching timer
• KNX-Bus power required only

It is able to drive a 5 A per channel, 12-24 VDC LED strip – that is a sum of 480 Watt dimming power or 120 Watt for each channel for 24 V LEDs.In device additionally a 16 A switching actuator with two timers is integrated. Thus, the LED power supply is powered on by the actuator if needed or turned off to minimize standby losses of the LED power supply. 

It is able to drive a 5 A per channel, 12-24 VDC LED strip – that is a sum of 480 Watt dimming power or 120 Watt for each channel for 24 V LEDs.In device additionally a 16 A switching actuator with two timers is integrated. Thus, the LED power supply is powered on by the actuator if needed or turned off to minimize standby losses of the LED power supply. 

• Up to 48 telegrams/second routing performance
• Up to 35 telegrams/second tunnelling performance
• Up to five KNXnet/IP tunnel connections
• Integrated display
• 10/100 MBit Ethernet interface
• Power over Ethernet or ext. 16-24 AC or 20-30V DC
• Battery buffered RTC
• SNTP server
• Telnet server

• • Up to 48 telegrams/second routing performance
  • Up to 35 telegrams/second tunnelling performance
  • Up to five KNXnet/IP tunnel connections
  • Integrated display
  • 10/100 MBit Ethernet interface
  • Power over Ethernet or ext. 16-24 AC or 20-30V DC
  • Battery buffered RTC
  • SNTP server
  • Telnet server

IT is a bidirectional meter for measurement of active and reactive energy or power, respectively. Further it features an analysis of power supply quality.Measurements can be performed in a 3-phase system or in three independent 1-phase system.(current, voltage, active power, reactive power, active energy, reactive energy, power factor, THD-U, THD-I harmonics, unbalanced load, zero system current) 

• Voltage: 24 V DC via KNX BUS
• typ. power input: 7 mA
• Detection area: vertical 360°
• Range:
  max. Ø 24 m across
  max. Ø 8 m towards
  max. Ø 6,4 m smaller movements
• Recommended mounting height: 2.5 m
• Degree / class of protection: IP20 / Class II
• Ambient temperature: -25 °C to +55 °C
• Housing: Polycarbonate, UV-resistant
• Brightness set value: 5 - 1200 Lux 

he available parameters allow you to define the following outputs:

• Meter value (m³)
• High-resolution meter value (10 l)
• Meter status 
• Serial number and meter number 
• Relative up counter Meter value / Reset
• Relative down counter Meter value / Reset / Zero
• Output 15min / 60min difference (m³)
• Due date billing Date / Set     

he available parameters allow you to define the following outputs:

• Meter value (m³)
• High-resolution meter value (10 l)
• Meter status 
• Serial number and meter number 
• Relative up counter Meter value / Reset
• Relative down counter Meter value / Reset / Zero
• Output 15min / 60min difference (m³)
• Due date billing Date / Set     

The KNX-Sensor Temperature SK01-T-ESTF-50-Silikon with the probe is used for temperature detection of fluid and gaseous media in piping and tubes. The integrated KNX bus coupler does not need additional auxiliary supply.The transducer with the bus coupler is enclosed in a durable, sealed,glass ball-reinforced plastic casing which fulfils protection degree IP65.   

The KNX-Sensor Temperature SK01-T-ESTF-100-Silikon with the probe is used for temperature detection of fluid and gaseous media in piping and tubes. The integrated KNX bus coupler does not need additional auxiliary supply.The transducer with the bus coupler is enclosed in a durable, sealed,glass ball-reinforced plastic casing which fulfils protection degree IP65.   

The KNX-Sensor Temperature SK01-T-ESTF-50-PVC with the probe is used for temperature detection of fluid and gaseous media in piping and tubes. The integrated KNX bus coupler does not need additional auxiliary supply.The transducer with the bus coupler is enclosed in a durable, sealed,glass ball-reinforced plastic casing which fulfils protection degree IP65.   

The KNX-Sensor Temperature SK01-T-ESTF-100-PVC with the probe is used for temperature detection of fluid and gaseous media in piping and tubes. The integrated KNX bus coupler does not need additional auxiliary supply.The transducer with the bus coupler is enclosed in a durable, sealed,glass ball-reinforced plastic casing which fulfils protection degree IP65.   

Time switch for home automation 8-ch Bus system KNX, Other bus systems None, Daily program, Weekly program, Annual program.External programming, Number of channels 8, Summer-/winter switchover, Radio-controlled (DCF77), GPS (global positioning system), Bus connection included, Sub-clocks controllable over bus-system, Autonomy 70000h, Degree of protection (IP) IP20.

voltage input: 230 V AC (50Hz)

output current: 960 mA

Integrated choke

LEDs for operation, bus reset and programming mode

Integrated bus-connection with voltage and current measurement

Data output on KNX bus via group object and visible on display

KNX objects for voltage, current and power measurements

KNX alarm functions

Housing temperature measurement

AUX with 600mA additional output

Alimentatore KNX 640mA DATEC 1630.02150/90100 DIN con Uscita Ausiliaria 30V.

English description pending.

Gateway Attuatore KNX/DALI da Incasso DATEC 1630.03140/70100 – 8 Canali UP.

English description pending.

Gateway Attuatore KNX/DALI DATEC 1630.04140/70100 – 8 Canali per Controsoffitto.

English description pending.

Power Supply KNX max Current 320mA. Input Voltage 230/110 VAC – 50/60Hz.

Power Supply KNX max Current 160mA. Input Voltage 230/110 VAC – 50/60Hz.

BX-2XIO is a 2-channels push button interface used to acquire external commands.The device provides control functions for load control, the opening and closing of shutters, the adjustment of a light source and the selection of scenarios.Some of these functions exploit the possibility of recognizing the prolonged closure of the auxiliary contact to carry out the command desired.

Attuatore Multifunzione KNX Blumotix BX-MFB08 – 8 Canali 16A DIN.

English description pending.

Miniserver KNX IP Blumotix BX-MS02 – Server DIN per Supervisione e Controllo Remoto Domotica.

English description pending.

K24 is the code to identify second generation of our Kairos 4 inch touch panel.The electronic system has been completely redesigned for improved performance and to have a significant costs reduction.Like the previous version this device has an internal KNX interface that allows connection directly to the bus cable. 

K24 is the code to identify second generation of our Kairos 4 inch touch panel.The electronic system has been completely redesigned for improved performance and to have a significant costs reduction.Like the previous version this device has an internal KNX interface that allows connection directly to the bus cable. 

Theo 7 touch panel comes programmed with a standard graphic display pre-set for controlling the Lights, Windows and Climate. Other functions can be added and browsed through, such as utility Loads control, Video camera control, Timer and Chrono Thermostat enabling and Scenario programming.

The new THEO 10 Touch Panels allow any KNX system to be controlled in a simple, user-friendly manner..This model have a built-in IP video door phone function, compatible with the best brands of IP outdoor stations (2N, Alphatec, etc.), with H.264 type image quality and SIP protocol audio signal transmission.    

The new THEO 10 Touch Panels allow any KNX system to be controlled in a simple, user-friendly manner..This model have a built-in IP video door phone function, compatible with the best brands of IP outdoor stations (2N, Alphatec, etc.), with H.264 type image quality and SIP protocol audio signal transmission.  

Rectangular Glass Cover (120mm x 80mm)

Rectangular Glass Cover (120mm x 80mm)

Thermostat KNX KRISTAL with Comfort Management, Precomfort, Economy and Frozen is provided with a humidity sensor with measuring and managing the dewpoint.

Thermostat KNX KRISTAL with Comfort Management, Precomfort, Economy and Frozen is provided with a humidity sensor with measuring and managing the dewpoint.

The Touch panel can be used to control the switch, dimming, blinds, and scene, etc. Each button of the Touch panel correspond one LED with two colors indication. The device can be installed in a conventional 86 mm wiring box.

The Touch panel can be used to control the switch, dimming, blinds, and scene, etc. Each button of the Touch panel correspond one LED with two colors indication. The device can be installed in a conventional 86 mm wiring box.

The Touch panel can be used to control the switch, dimming, blinds, and scene, etc. Each button of the Touch panel correspond one LED with two colors indication. The device can be installed in a conventional 86 mm wiring box.

Wide apply in stadium,high-rise building,crane,pier,airport,hangar factory and other outdoor large area lighting fields.The super brightness led flood light is perfect replace 200W-300W HPS traditional light,energy save up to 50%.  

NK5025V15-A is a vandal-proof dome camera with IR illuminators, the camera adopts weather-proof and vandal-resistant housing design, withstanding harsh environments, this camera can be suitable for both indoor and outdoor installation for diversity of IP surveillance applications.  

NK4025D1-D is a vandal-proof dome camera adopts IP68 weatherproof and IK10 vandalproof design to effectively withstand harsh conditions - such as rain, dust, wind, sand, salt, extreme hot and cold temperature etc.can be suitable for any indoor and outdoor HDTV IP video surveillance applications including residences, offices, schools, libraries, churches, transportation etc.  

NS2025VB58 is a Full HD 1080p bullet type IP camera that utilizes Panasonic MN34229PL CMOS image sensor offering True-WDR function with 120dB wide dynamic range. This camera can deliver 2MP (1920x1080) resolution video with vivid color and superior image quality.  

The NS4025VB58 is  a high-end IP camera to deliver video streams with 4MP (2592x1520), 3MP (2048x1520), 1080P (1920x1080) resolution. This camera is based on OmniVision OV4689 1/3-type 4MP progressive CMOS image sensor and Hi3516D/A codec engine hardware design.   

NS5025VB58-A is a high-quality, high-performance 5MP Full HD Network IR Bullet Camera, it has a 1/1.8-inch progressive scan CMOS image sensor with IR-CUT filter built-in to capture the video. Thanks to its robust video encoding processor – Hi3516A, this camera can provide maximum 5MP@30fps video encoding, with three different compression standard (H.265/HEVC, H.264, MJPEG).     

The switch actuators are the modular installation devices, with 2, 8 and 12 outputs for selection, using EIB BUS connection terminals to connect to the system. The switch actuators are connected to the AC power supply directly instead of an extra voltage supply. 

The switch actuators are the modular installation devices, with 2, 8 and 12 outputs for selection, using EIB BUS connection terminals to connect to the system. The switch actuators are connected to the AC power supply directly instead of an extra voltage supply. 

The switch actuators are the modular installation devices, with 2, 8 and 12 outputs for selection, using EIB BUS connection terminals to connect to the system. The switch actuators are connected to the AC power supply directly instead of an extra voltage supply. 

The switch actuators are the modular installation devices, with 2, 8 and 12 outputs for selection, using EIB BUS connection terminals to connect to the system. The switch actuators are connected to the AC power supply directly instead of an extra voltage supply. 

Uscita Analogica KNX DATEC 1630.02131/57100 – 4 Canali 0-10V DIN per Valvole, Ventilazione e Motori.

English description pending.

The Universal Interfaces can install to be system with EIB/KNX bus and other device, which are mainly use in building control system. The functions are both simple to operate and intuitive, users can program it according to the requirement to implement the function systematically.

Temperature control panel is a device to control indoor temperature .It adjust the room temperature and relative humidity according to the measured temperature and relative humidity, generally implemented by controlling indoor temperature controller and fan coil actuator one the bus.

The switch actuators are the modular installation devices, with 2, 8 and 12 outputs for selection, using EIB BUS connection terminals to connect to the system. The switch actuators are connected to the AC power supply directly instead of an extra voltage supply. 

The switch actuators are the modular installation devices, with 2, 8 and 12 outputs for selection, using EIB BUS connection terminals to connect to the system. The switch actuators are connected to the AC power supply directly instead of an extra voltage supply. 

The switch actuators are the modular installation devices, with 2, 8 and 12 outputs for selection, using EIB BUS connection terminals to connect to the system. The switch actuators are connected to the AC power supply directly instead of an extra voltage supply. 

Attuatore Dimmer LED KNX Weinzierl IO 534 CV (4D) – 4 Uscite PWM RGB/RGBW/Tunable White, Alimentato da Bus.

English description pending.

The LED Dimming Actuator KNX IO 534 CV (4D) is a compact RGB / RGBW / Tunable White dimming actuator with 4 outputs (constant current). The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. In LED Dimming Actuator KNX IO 534 CV (4D) several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and three LEDs allow a local operation and a visualization of the device state. In addition to the output channels the device includes 16 independent functions for logic or timer control.

The LED Dimming Actuator KNX IO 532 (1D1O) is a compact combined dimming/switching actuator with 1 PWM dimming output for LEDs and 1 bi-stable relay output. The dimming actuator can be used e.g. for LED panels or stripes. Besides controlling the dimmer by switching, rel. dimming and dimming value, several optional functions are integrated, including scenes, automatic, slumber function or staircase light.The LED Dimming Actuator KNX IO 532 (1D1O) provides the function for universal outputs including scene control, timer, staircase lighting and heating valves (PWM for thermoelectric valve drives). Two push buttons and three LEDs allow a local operation and a visualization of the device state. In addition to the output channels the LED Dimming Actuator KNX IO 532 (1D1O) includes 16 independent functions for logic or timer control. 

Attuatore Dimmer KNX Weinzierl IO 530 (1D2I) – 1 Canale Dimmer 230V + 2 Ingressi Binari, 1TE.

English description pending.

The Universal dimming actuator KNXIO 530 (1D2I) is a compact mains dimmer for 230 V ~ with one output and two binary inputs. The dimming actuator supports phase control or phase section and is thus suitable for all dimmable 230 V lamps (eg incandescent lamps, dimmable LED lamps, halogen lamps). The dimming channel offers various comfort functions, including scenes, automatic, snooze function, staircase lighting and sequencer.The inputs of Universal dimming actuator KNXIO 530 (1D2I) can be controlled via conventional switches with an external voltage of 230 V. In addition to the output and input channels, the Universal dimming actuator KNXIO 530 (1D2I) contains 16 independent logic or timer functions. Two buttons and three LEDs on the front of the device allow local operation and visualization of the device status.

The Blind Actuator KNX IO 520 (1J2I) is a compact blind actuator with two additional binary inputs. The actuator is used to control a blind, a shutter or a window drive. The relay contacts are electrically interlocked. The inputs Blind Actuator KNX IO 520 (1J2I) can be connected to conventional switches with an external voltage of 12 to 230 V. In the not configured state the binary inputs control the actuator channel. Via commissioning the device using ETS® software the binary inputs can be used independently. Two push buttons and three LEDs allow a local operation and a visualization of the device state. In addition to the output and input channels the Blind Actuator KNX IO 520 (1J2I) includes 16 independent functions for logic or timer control.

• ▪ 1 shutter output, 230 V∿, 8 A
• ▪ Drive directions electro-mechanically locked against each other
• ▪ For blinds, shutters or window drives
• ▪ Approach position via time calculation
• ▪ 2 inputs 12..230 V⎓∿, galvanically isolated
• ▪ Switching, dimming, shutters, scenes, pulse counter
• ▪ Integrated logic and timer functions
• ▪ Connections: KNX, plugable screw terminals for IO
• ▪ For DIN rail, width 1 unit (18 mm)

KNX USB Interface Stick 332 - Stick USB/KNX con Long Frame, BAOS V2 e Adattatore USB-C.

English description pending.

The USB INTERFACE KNX STICK 332 is a data interface between a PC or laptop and the KNX installation bus. USB INTERFACE KNX STICK 332can be used as a programming interface for ETS® Software Version 3 (or higher) and supports KNX long frames. Long telegrams enable a faster download to devices that can receive these telegrams.

The LEDs in the device indicate the operating status and communication errors on the bus. The USB connector is galvanic isolated from the KNX bus.

This USB INTERFACE KNX STICK 332 can be used to program KNX Secure devices with the ETS.

KNX RF USB Interface Stick 340 - Stick USB/KNX RF per Programmazione ETS Wireless e KNX Secure.

English description pending.

 RF USB INTERFACE KNX STICK 340 interface allows establishing a bidirectional connection between a PC or a laptop and the KNX RF wireless network. The device complies with the specification of KNX RF and supports the protocol cEMI. This RF USB INTERFACE KNX STICK 340 can be used to program KNX Secure devices with the ETS. The  RF USB INTERFACE KNX STICK 340 is compatible with ETS 5 (or higher). For software integration (Windows or Linux) of this interface the free SDK kDrive express is available. The power is supplied via the USB port.In addition to the telegram interface via cEMI, the KNX RF USB Interface Stick 340 includes a complete KNX Stack with communication objects and BAOS protocol V2. Thus, the stick offers the possibility to extend devices with USB connection to full KNX devices, which can even be programmed by ETS.

Attuatore di Commutazione KNX Weinzierl IO 511.1 secure (1O2I) – 1 Uscita Relè 230V/16A + 2 Ingressi, Sostituto Relè a Impulsi.

English description pending.

Compact KNX actuator: 1 relay output 230V~/16A + 2 binary inputs galvanically isolated. KNX replacement for impulse switches. KNX Security. 1 DIN module. Art. 5327.

Attuatore di Commutazione KNX Weinzierl IO 510.1 secure (2O) – 2 Uscite Relè 230V/10A, KNX Data Security.

English description pending.

Compact KNX switching actuator with 2 bistable relay outputs 250V~/10A. Staircase function, heating actuator, integrated logic, KNX Security. 1 DIN module (18 mm). Art. 5444.

The KNX TP Blue IO 551 CC secure is a compact RGB / RGBW / Tunable White dimming actuator with 4 constant current dimming outputs. The dimming actuator can be used e.g. for LED panels or stripes with RGB / RGBW / Tunable White configuration or as 4 independent dimmer channels. Every configuration allows controlling the channel by switching, rel. dimming and dimming value. Several comfort functions are integrated as well, including scenes, slumber fading, staircase light and sequencer. Two push buttons and five LEDs allow a local operation and a visualization of the device state. In addition to the output channels the device includes 16 independent functions for logic or timer control. The device supports KNX Data Security.

KNX IP BAOS 777 - Residential Gateway KNX con Web Server, Visualizzazione, Astrotimer e BAOS V2.1.

English description pending.

The KNX IP BAOS 777 is a powerful universal device for KNX installation: Thanks to the integrated web server, the device enables the visualization and control of buildings, rooms and functions in a standard web browser on a PC or mobile devices such as smartphones and tablets. The new, integrated e-mail function allows individual notification of several recipients, e.g. in case of status changes or an alarm. The integration of a Date & Time Server (NTP) makes it possible to obtain the date and time automatically via the Internet and to synchronize one’s own KNX installation. Extensive time functions allow the realisation of a powerful KNX time switch with weekly function.The configuration is done exclusively with the ETS software – no extra software or tool is required. The device also offers the function of a KNX IP interface (KNXnet/IP), for example as a programming interface for the ETS. Developers can access all functions via an API with BAOS RESTful Web Services. This allows the device to be used as an application-specific gateway, connecting the KNX bus to the existing IP infrastructure. The KNX IP BAOS 777 represents a powerful residential gateway for building control with smallest size and minimal power consumption.

Pulsante Wireless KNX Weinzierl RF/ENO Push Button 440 secure – Ibrido KNX RF + EnOcean, Serie MATCH 55.

English description pending.

The KNX RF / ENO Push Button 440 secure unites two wireless protocols in one device: EnOcean and KNX RF. Out of the box the push button operates in EnOcean mode. EnOcean Secure can be enabled via pressing a key combination. By configuration with the ETS® the push button switches to KNX RF mode with optional support of KNX Data Security. Via a factory reset the device can be switched back to EnOcean protocol.

KNX IP LineMaster 762.1 secure - Alimentatore Bus con Router IP e Interfaccia Secure.

English description pending.

The KNX IP LineMaster 762.1 secure combines the essential functions of a KNX bus line: KNX power supply with choke, KNX IP router and KNX IP interface. In addition to the bus voltage the power supply offers an auxiliary voltage.

The KNX IP router in the KNX IP LineMaster 762.1 secure allows forwarding of telegrams between different lines through a LAN (IP) as a fast backbone. Using the embedded KNX IP interface, the KNX line can be connected directly to a PC (e.g. by ETS). The device supports KNX Security which can be enabled in ETS. As secure router the device allows coupling of not secured communication on KNX TP to a secured IP backbone. Also for the interface functionality (unneling) KNX security prevents from unauthorized access. The IP address can be obtained by a DHCP server or by manual configuration (ETS) respectively.

This device works according to the KNXnet/IP specification using the core, the device management, the tunneling and the routing part. The KNX IP LineMaster 762.1 secure has an extended filter table for main groupls 0 to 31 and is able to buffer up to 150 telegrams.

Alimentatore KNX Weinzierl PowerSupply USB 367 – 640mA con Display OLED, Interfaccia USB e Funzioni Logiche.

English description pending.

USB POWER SUPPLY 367 KNX Secure is a 640 mA bus power supply with high efficiency and a small footprint of only 4 units (72 mm). The USB POWER SUPPLY 367 KNX Secure device has a bus choke, an integrated USB interface (Micro USB connector) and additionally provides an output for auxiliary power supply. Via the integrated KNX node USB POWER SUPPLY 367 KNX monitors the output current, the bus voltage and the temperature in the switchgear. The 367 KNX Secure device has various logic functions for application purposes. The configuration of the 367 KNX Secure is done with the ETS (version 4.2 or later). An easy to read OLED display on the front panel allows the user to view the operating parameters locally on the USB POWER SUPPLY 367 KNX Secure. This USB interface can be used to program KNX Secure devices with the ETS.