• Eight completely programmable independent touch areas. 
• Includes a discretized PI regulator to achieve greater comfort and energy savings. 
• Built-in humidity sensor. 
• Dew point measurement according to relative humidity and temperature. 
• Arithmetic Logic Unit 
• Timers/counters.
• Also available in the White version

• Temperature sensor 0 to 51 ° C
• Temperature Controller: 2 points, or continuous PWM
• PI control algorithm
• Control system hot / main heat output and additional on/off
• Flush mounting in box with vented cap mechanism
• Simple logic unit  

• 2 Regulation channels for LED lighti ng 
• 2 low voltage input (SELV) for pushbutton (non programmable) 
• 8 Programmable scenes executed from bus commands 
• Remote enable / disable of bus control
• Overload circuit protection and thermal protection 
• Digital regulation control based on microcontroller with more than 200 regulation points 
• Last position memory in case of power failure 

The panel has been designed to show all controls on a single page including 8 (up to 32 into 4 pages). It also includes a specific interface for climate control with an internal thermostat. The ability of the panel to generate a wifi network to allow it to be controlled locally from any iOS or Android device, simply by downloading the official Ingenium applications. 

It is device, for Heating or Cooling applications in offices, hotel rooms and much more.The fancoil can be used in Analog 0-10VDC or PWM mode. The fancoil actuator is able to drive up to three fan speeds and an additional 230VAC relay output.The device has two physical inputs, the first for connecting a local temperature sensor and the second to be used as binary input or as window contact input. 

It is a flush mounted device,for ceiling fan applications in offices, hotel rooms..It is used for varying ceiling fan speed as determined by KNX input or control systems.Also,speed can be varied by push buttons directly connected to the MOTOR CONTROL device.The ceiling fan must be of standard motor type, without control electronics. If using multiple speed fans, always force fan in max speed.

Integrates an indoor Daikin climate unit  with KNX system.Five operating modes (auto, heat, cold,  ventilation and dry). Three fan speeds (low, medium, high). Includes energy saving mode. Arithmetic-logic unit and timers/counters. 

Bi-directional communication gateway between KNX protocol and Fermax Smile Dominium video intercom.Allows to control and manage KNX devices from the Smile Dominium video intercom, using a project uploaded from the SiDEKNX software.Direct connection to the Fermax Smile Dominium video entry system and the KNX bus.  

It is possible to adjust the presence sensor sensitivity in an easy way,selecting between 3 different levels or personalizing by yourself.It includes parameters to define regulation steps,to establish deviations, or to calibrate it.It is also possible to change between auto and manual mode, defining the behavior when it changes between those two options.It also includes an additional thermostat 

Capacitive push-button with 4 independent touch areas, completely programmable.LED indicator associated with each touch areas. Square format. Universal distribution box size. In-built temperature sensor to measure and to send the information to KNX BUS. 

• Supply: 29V DC from KNX BUS
• Size: 88 x 88 x 8mm
• Mounted on universal box, screwed on wall

The webserver all

ows to control a KNX installation using an iOS, Android or Samsung Smart TV devices remotely through the Ingenium server or a PC connected to the internet with any type of web browser. This webserver has Wi-Fi connectivity and 1 Ethernet port (10 Mbit/sec). The control applications are completely free.  

Download IL DATASHEET

Download IL MANUALE

Download IL SOFTWARE 

R27A is a fashionable, SIP-enabled IP video door phone with a RF card reader and a numeric keypad. It enables easy monitoring of an entrance area and convenient entry control. The ability of granting or denying access based on talking to and seeing your visitors as if in person, gives one a true sense of security and great peace of mind. 

• Premium audio and video quality
• Real-time entrance monitoring
• Remote door opening 
• RF card reader and numeric keypad
• SIP/ONVIF/Wiegand/PoE/IP65
• Anti-cold version available

Physical Features

• Body material: aluminum panel
• Camera: 3M pixels, with automatic lighting
• Button: 1 call button
• RF card reader: 13.56MHz
• PoE IEEE802.3af
• Power consumption: 12V DC input, <12W
• G-sensor for tamper alarm
• Enclosure rating: IP65
• Installation: flush mounting or wall-mounting
• Dimensions: 190x110x35mm

Download Datasheet

R27A is a fashionable, SIP-enabled IP video door phone with a RF card reader and a numeric keypad. It enables easy monitoring of an entrance area and convenient entry control. The ability of granting or denying access based on talking to and seeing your visitors as if in person, gives one a true sense of security and great peace of mind. 

• Premium audio and video quality
• Real-time entrance monitoring
• Remote door opening 
• RF card reader and numeric keypad
• SIP/ONVIF/Wiegand/PoE/IP65
• Anti-cold version available

Physical Features

• Body material: aluminum panel
• Camera: 3M pixels, with automatic lighting
• Button: manager center, dial key and clear key
• Keypad: numeric keypad
• RF card reader: 13.56MHz and 125 kHz
• PoE IEEE802.3af
• Power consumption: 12V DC input, <12W
• G-sensor for tamper alarm
• Support infrared sensor
• Enclosure rating: IP65 
• Operating Temperature: -4° to 131°F / -20° to 55°C (Anti-cold version available: -40 ~ 131 °F / -40 ~ 55°C)
• Installation: flush mounting or wall-mounting
• Dimensions: 280x130x68mm

Download Datasheet

The KNX POWER SUPPLY 640mA is a DIN Rail mounted KNX device with integrated choke, to directly power a KNX line. An auxiliary 30V output is available for some extra loads, as displays, binary inputs, …

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose. 

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose. 

IT82 is a SIP-enabled IP indoor  monitor for multifunctional communications from inside your home. It enables high-quality audio and video communications with its door phone and between indoor units in different rooms. All in-home automation devices can be easily managed and controlled by it. It is even capable of importing mobile applications for home entertainments. At the core of all these is its large capacitive touch screen and the intuitive Android Operating System.

Physical Features

• Display: active matrix TFT, transmissive type
• Screen: 7” capacitive touch screen
• Button: 5 capacitive, programmable pushbuttons
• Memory: RAM-2GB, Flash-4GB
• PoE IEEE802.3af
• Power consumption: 12V DC input, <12W
• Aspect ratio: 16:9
• Resolution: 1024x600
• Brightness: 300nits (cd/m²)
• Contrast: 800:1
• Color depth: 24-bit, 16M colors
• Illumination: edge-lit LED
• Viewing angle: ±80°left, ±80°right;±60°upper, ±70°lower
• Optional 1M-pixel camera
• Optional Wi-Fi and Bluetooth
• Installation: US or European electrical wall box mounting
• Dimensions: 232 x 160 x 21 mm

Akuvox smart indoor monitor IT83R is a multifunctional modern in-home intercom featuring Android OS 6.0 and 10-inch capacitive touch screen. It provides exceptional audio and video communication with door phone and room-to-room communication via SIP 2.0 protocol, and supports real-time entrance monitoring via ONVIF/RTSP. It comes with rich interface that enables easy integration with other digital systems, such as home automation and telehealthcare.

• 10-inch touch screen
• Intuitive Android Operating System 
• Alexa Integration
• Premium audio and video quality
• Home automation integration
• Android 6.0/SIP/RTSP/PoE

Touch Screen Display

• Display Mode: Normally black, Transmissive
• LCD Size: 10 inch (Diagonal)
• Aspect Ratio: 16:9
• Resolution: 1280x800
• Contrast ratio: 800:1
• Luminance: 350 cd/m ²
• Viewing Angle: ±89° Left, ±89° Right,
• Viewing Angle: ±89° Upper, ±89° Lower
• Touch Screen: Projected Capacitive

Mechanical Parameter

• Dimensions (W x H x D): 251 x 182.5 x 22 mm

• Includes PI regulator for controlling temperature with higher accuracy for better energy efciency and comfort 
• On/Off, PWM or continuous temperature controller for main heat/cool system and additional. 
• Dew point measurement according to relative humidity and temperature.
• Easy Logic Unit.
• Available in the White version
• Optional Front glass interchangeable,  print customizable. 

Presence detector with radio- frequency technology for hidden installation. 360º detection through non-metallic surfaces for installation in technical and false ceilings.Safe against sabotage and non- desired manipulation due to its hidden installation. Suitable for lighting, motion detection, intrusion control, etc.

• 3 Regulation channels that can be controlled individually or simultaneously 
• Maximum operating output current: 3A per channel
• 8 Programmable scenes executed from bus commands 
• PWM dimming method 
• Overload circuit protection 
• Digital regulation control based on microcontroller more than 200 regulation points 
• Last position with memory in case of power failure

The Analog output 0-10V, 4 channels, is controlling 4 single 0-10V outputs.These are used, for example, to control analog 0-10V valves, in accordance with the requirements of room control units, mainly in cooling or heating applications in offices, hotel rooms, …