• Universal Interface with 4 binary inputs and 4 LED outputs.
• The Universal Interface has 4 channels which can be parameterised as inputs or outputs, e.g. for
  connection of conventional pushbuttons, free-voltage motion detectors, etc.
• The interface can evaluate at its potential-free inputs up to 4 pushbutton/switch states with a
  common reference potential and send the corresponding telegrams.
• The telegrams may be for switching or dimming, blind/shutter control, value transmitter applications
  (light level, temperature,…), light scene control or pulse counting.
• As an alternative, the four channels can control four LEDs as independent outputs.
• The outputs are protected against short circuits, overload and wrong polarity.
• This device is flush mounted in a universal box, behind the pushbutton/switch.
• Dimensions: 38 x 42 x 15mm.
• Programming and commissioning by ETS4 or later.

• Wireless Luminosity sensor transmitter with setpoint temperature value knob for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brightness value and the setpoint value to the lighting actuator.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

A 12 channel KNX actuatorfor monitoring electrical loads with outputs up to 16A.  The device provides the traditional switching functions, complete with notification of the state, stop command, timer functions and scenarios. It also has a set of logical functions consisting of 16 freely configurable communications objects (OR, AND, XOR). The outputs can be pre-set individually by ETS.  

A 8 channel KNX actuatorfor monitoring electrical loads with outputs up to 16A.  The device provides the traditional switching functions, complete with notification of the state, stop command, timer functions and scenarios. It also has a set of logical functions consisting of 16 freely configurable communications objects (OR, AND, XOR). The outputs can be pre-set individually by ETS.  

A 4 channel KNX actuatorfor monitoring electrical loads with outputs up to 16A.  The device provides the traditional switching functions, complete with notification of the state, stop command, timer functions and scenarios. It also has a set of logical functions consisting of 16 freely configurable communications objects (OR, AND, XOR). The outputs can be pre-set individually by ETS.  

• The KNX RF / TP coupler is a compact KNX Radio coupler. Connect the KNX RF devices of a radio line with the KNX Twisted Pair Bus.
• You have a filter table (8k bytes).
• Supports long frames compatible with ETS® ETS5 or higher software.
• The keys on the front allow you to disable the telegram filter for testing purposes.
• The LEDs indicate the operating conditions and communication errors on the KNX bus.
• The power supply is supplied via the KNX bus (main line).
• Programming and commissioning using ETS5 or later.

It is device, for Heating or Cooling applications in offices, hotel rooms and much more.The fancoil can be used in Analog 0-10VDC or PWM mode. The fancoil actuator is able to drive up to three fan speeds and an additional 230VAC relay output.The device has two physical inputs, the first for connecting a local temperature sensor and the second to be used as binary input or as window contact input. 

It is a flush mounted device,for ceiling fan applications in offices, hotel rooms..It is used for varying ceiling fan speed as determined by KNX input or control systems.Also,speed can be varied by push buttons directly connected to the MOTOR CONTROL device.The ceiling fan must be of standard motor type, without control electronics. If using multiple speed fans, always force fan in max speed.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless 1-channel Thermostat actuator for HVAC control.
• It incorporates a potentiometer which allows setting the desired temperature avoiding any undesired manipulation.
• Every time it receives a signal of temperature from the sensor it will be compared with the already set in the thermostat and will act accordingly on its relay.
• It also can receive telegrams from door/window contacts or presence detectors.
• Up to 16A switching capacity with free-voltage relay.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Modular installation device. DIN-rail mounting. 1-module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: SE KNX 001, SE KNX 003, SE KNX 004, DP KNX 001 & CO KNX 002.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless 1-channel Switch actuator for general purpose.
• Up to 16A switching capacity with non-free voltage output.
  Two different operation modes:
  · Switch ON/OFF.
  · Timer: 3sec ~ 5min.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• A conventional pushbutton can be wired for local control.
• DIN-rail mounting. Dimensions: 1 module wide.
• 230V-operated.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

• Wireless wall-mounted Infrared PIR motion detector for lighting control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• As soon as it detects movement, the sensor sends the ON signal to the linked receiver and its
  contact keeps closed. The ON time must be set on the receiver.
• Wall or ceiling mounting installation.
• Coverage: 180º and Ø10m at 2m high.
• Power Supply: 2 x 3V AA Lithium batteries L91. Working life over 15 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: IT KNX 001, MI KNX 001 & CO KNX 002.

• Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
• Built-in light sensor, allowing to limit the operation of the detector to daylight.
• It has 2 operation modes:
  · Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 & CO KNX 002.
  · Presence detector: useful for heating and air conditioning control.
• Compatible with the actuators: TM KNX 001 & CO KNX 002.
• Incorporates Temperature sensor
• Coverage: 360º and Ø7m at 2,5m high.
• Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
• Radio-frequency: 868,4MHz.

• Wireless Luminosity sensor transmitter for daylight control.
• It is designed for the automatic control of lighting depending on the natural light.
• It sends the existing brigthness value to the lighting actuator for constant light control operation.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Dimensions: 78 x 28 x 23mm.
• Compatible with: RE KNX 102, RE KNX DA2 & CO KNX 002.

• Wireless Temperature sensor with desired temperature value control knob.
• This sensor sends the following variables:
  · Measured temperature value.
  · Temperature setpoint value.
  · State (Standby or Auto).
• Incorporates a wheel to set the desired temperature in the room.
• Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
• Dimensions: 80 x 30 x 26mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• The Radio Remote Control sends KNX telegrams when one of the keys is presse depending on its parameterisation.
• The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
• Incorporates 5 independent channels, 1 main channel and 5 scene channels.
• Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1,RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 & RE KNX DA1.

• One channel interface for 2-fold pushbutton.
• Dimmer: Connects, disconnects or dims the linked actuator. It sends ON/OFF or Dimming_Up/Dimming_Down depending on which of the two buttons is pressed the duration of the action.
• Blinds/Shutters: Controls a linked blind actuator. It sends Step_Up/Step_DOwn or Move_Up/Move_Down depending on which of the two buttons is pressed and the duration of the action.
• Scenes: Saves and recovers two different scenes (one scene in each button). It sends Scene_Save or Scene_Load depending on the duration of the action.
• Installaton in standard mechanism box, behind pushbutton.
• Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX DMS, RE KNX LE1 & RE KNX LE2.

Power Supply KNX max Current 320mA. Input Voltage 230/110 VAC – 50/60Hz.

BX-DM03 is a 4-channels dimmer actuator for LED lamps with current-mode control.The channels can be programmed to work independently with white lamps or can be synchronized to drive the color of a RGB / RGBW lamp.Each channel can be programmed via dip switches to supply the current for the type of lamp installed in accordance with the predetermined standard values: 350mA, 700mA and 1000mA.

BX-2XIO is a 4-channels push button interface used to acquire external commands.This is the new push-button interface equipped with outputs for monitoring the warning LEDs found in modern domestic series. .The device provides control functions for load control, the opening and closing of shutters, the adjustment of a light source and the selection of scenarios. 

BX-MFB12 is a multifunction 12-channels actuator, programmable with ETS to perform different tasks like switching loads, open and close shutters and blinds, drive valves operating in PWM and control 2 or 4 pipe fancoil.Each outputs uses bistable relays with 16A maximal load. Block terminals are very wide to insert wires with a section up to 5 mm2.

A KNX device for measuring Alternating Electrical Current. This device measures the alternating current absorbed on an electrical line and indirectly provides the power values that can be used to determine the amount of electrical power consumed.The 3 channels can be programmed independently by ETS to carry out energy saving operations. Current clamps not included 

Kristall offers all the safety and durability advantages of a capacitive keyboard, since there is no mechanical wear of any kind, and ease of use is improved with the introduction of luminous and acoustic feedback.Kristall offers the complete KNX command set needed to control any type of device: On/Off commands, light dimming, window actions and transmission of scenarios.

Kristall offers all the safety and durability advantages of a capacitive keyboard, since there is no mechanical wear of any kind, and ease of use is improved with the introduction of luminous and acoustic feedback.Kristall offers the complete KNX command set needed to control any type of device: On/Off commands, light dimming, window actions and transmission of scenarios.

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Universal dimmer for: incandescent or 230V halogen lamps, LV halogen lamps with electronic or inductive transformer and 230V or 12V ~ (with electronic transformer) dimmable LED lamps.
• Leading or trailing edge dimming technology.
• Control:
  • Pushbutton (wired),With memory: the lamps are switched on at previous level before being switched-off, the lamps are switched on at maximum level.
  • Wireless (KNX-RF), Remote control (RC KNX 01), Transmitter for pushbutton (EM KNX 002) or any other KNX-RF compatible transmitter.
• Installation into junction box.
• Wireless Master/Slave configuration: it is possible to enlarge the load capacity with one wired pushbutton and several dimmers RE KNX LE1

• Wireless 1-channel blind/shutter actuator or 2-channel switching actuator.
• Up to 16A switching capacity per channel with 2 free-voltage outputs.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Includes 2 auxiliary inputs which allow the local control.
• Dimensions: 107 x 53 x 34mm.
• 230V-operated.
• Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 002 & CO KNX 002.

• The 4-channels Analog/Digital interface is equipped with 4 independent channels which may be used as inputs for Analog or Digital signals.
• Each channel may be used depending on the parameterization by the ETS:
  • Binary input: the interface can evaluate at its potential-free inputs up to 4 pushbutton/switch states and send the corresponding telegram according to the configured setting as: Switch, Dimmer, Multiple Switch, Sequential Switch, Shutter/Blind control, Scene Control, Fixed/Forced value or Counter.
  • Analogue input: temperature sensor by connecting an external temperature probe (ST KNT 001 or ST KNT 002).
• Can be configured and enabled up to 4 independent Thermostats.
• Flush-mounting within universal box, behind the pushbutton/switch.
• The inputs are protected against short-circuit, overload and wrong polarity.
• Supply from the Bus. External supply is not required.
• Built-in KNX BCU (Bus Coupler Unit).
• Programming and commissioning by ETS4 or later.

• Wireless Temperature sensor transmitter with Probe for heating floors.
• It sends the temperature value in the place where the probe is installed.
• Specially-indicated for underfloor heating installations.
• Includes the following components:
  · Transmitter: captures the value from the temperature probe and transmits it via RF to the linked
    receiver.
  · Temperature probe: measures the temperature sensed at the tip of the probe. Must be connected
    directly to the transmitter via its original cable, which is double insulated. Tip of the probe is
    waterproof.
• The temperature value is sent every minute.
• Incorporates RF signal repeater function, which can be enabled or disabled as needed.
• Power supply: 230V~ 50Hz.
• Dimensions: 45 x 42 x 12mm.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

• Wireless Luminosity value transmitter for Sun protection function.
• It is designed for the automatic control of shutters or blinds.
• According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
• Luminosity is measured by the sensor attached to the window with a sticker.
• Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
• Dimensions: 78 x 28 x 23mm.
• Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: PE KNX 001 & CO KNX 002.

• Wireless Temperature value transmitter.
• Sends the temperature value measured in the place when:
  · The temperature value changes more than ±0,5ºC.
  · 60 minutes after the last transmission.
  · Pressing the inside link key.
• Dimensions: 78 x 28 x 23mm.
• Portable or wall fix mounted.
• Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
• Radio-frequency: 868,4MHz.
• Range: up to 100m (in the free field).
• Compatible with: TM KNX 001 & CO KNX 002.

BX-TU is the innovative push button interface equipped with an external temperature and humidiy probe to perform thermostat functions, humidy and dew point temperature control.The device is developed without a display unit or local buttons, therefore, setpoint temperature adjustment and visualization can be exclusively carried out via a Blumotix supervision system.

The KNX POWER SUPPLY 640mA is a DIN Rail mounted KNX device with integrated choke, to directly power a KNX line. An auxiliary 30V output is available for some extra loads, as displays, binary inputs, …

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose. 

The Datec KNX/DALI Actuator 1x 8 Outputs is a device for controlling and monitoring up to 8 DALI ballast. Each lamp may also be controlled manually using the buttons on the device. Part of the monitoring is directly visible on the device itself. This is useful for commissioning lamps and test the installation even without KNX Programming. KNX bus Power is sufficient for this purpose. 

Power Supply KNX max Current 320mA. Input Voltage 230/110 VAC – 50/60Hz.

Power Supply KNX max Current 160mA. Input Voltage 230/110 VAC – 50/60Hz.

BX-2XIO is a 2-channels push button interface used to acquire external commands.The device provides control functions for load control, the opening and closing of shutters, the adjustment of a light source and the selection of scenarios.Some of these functions exploit the possibility of recognizing the prolonged closure of the auxiliary contact to carry out the command desired.

BX-MFB04 is a multifunction 8-channels actuator.The device provides the traditional switch functions previously described for the BX-ACT08 model and additional functions for opening and closing shutters, adjusting blinds, monitoring valves with a PWM algorithm and controlling fan coil devices (with 2 or 4 pipes).   

BX-MS01 is a modern server with solid-state memory enabling to view and control functions in one’s Konnex system via remote devices connected to the TCP/IP network.The remote devices interact through an APP named KRIM which can be downloaded and installed on one’s terminal. iOS, Android and Windows 7 dedicated versions are available 

K24 is the code to identify second generation of our Kairos 4 inch touch panel.The electronic system has been completely redesigned for improved performance and to have a significant costs reduction.Like the previous version this device has an internal KNX interface that allows connection directly to the bus cable. 

Theo 7 touch panel comes programmed with a standard graphic display pre-set for controlling the Lights, Windows and Climate. Other functions can be added and browsed through, such as utility Loads control, Video camera control, Timer and Chrono Thermostat enabling and Scenario programming.

The new THEO 10 Touch Panels allow any KNX system to be controlled in a simple, user-friendly manner..This model have a built-in IP video door phone function, compatible with the best brands of IP outdoor stations (2N, Alphatec, etc.), with H.264 type image quality and SIP protocol audio signal transmission.    

The new THEO 10 Touch Panels allow any KNX system to be controlled in a simple, user-friendly manner..This model have a built-in IP video door phone function, compatible with the best brands of IP outdoor stations (2N, Alphatec, etc.), with H.264 type image quality and SIP protocol audio signal transmission.  

Rectangular Glass Cover (120mm x 80mm)

Rectangular Glass Cover (120mm x 80mm)

Thermostat KNX KRISTAL with Comfort Management, Precomfort, Economy and Frozen is provided with a humidity sensor with measuring and managing the dewpoint.

Thermostat KNX KRISTAL with Comfort Management, Precomfort, Economy and Frozen is provided with a humidity sensor with measuring and managing the dewpoint.